manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 583

NetBlazer

571

16 Warranty

General Information

EXFO Inc. (EXFO) warrants this equipment against defects in material and 
workmanship for a period of one year from the date of original shipment. 
EXFO also warrants that this equipment will meet applicable specifications 
under normal use.

During the warranty period, EXFO will, at its discretion, repair, replace, 
or issue credit for any defective product, as well as verify and adjust the 
product free of charge should the equipment need to be repaired or if the 
original calibration is erroneous. If the equipment is sent back for 
verification of calibration during the warranty period and found to meet all 
published specifications, EXFO will charge standard calibration fees.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED, 
IMPLIED, OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, THE 
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A 
PARTICULAR PURPOSE. IN NO EVENT SHALL EXFO BE LIABLE FOR 
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.

I

MPORTANT

The warranty can become null and void if:

unit has been tampered with, repaired, or worked upon by 
unauthorized individuals or non-EXFO personnel.

warranty sticker has been removed.

case screws, other than those specified in this guide, have been 
removed.

case has been opened, other than as explained in this guide.

unit serial number has been altered, erased, or removed.

unit has been misused, neglected, or damaged by accident.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды