EXFO FTB-1 Скачать руководство пользователя страница 570 | Manualshive

Страница: 570 / 675

EXFO FTB-1 Скачать руководство пользователя страница 570

Test Control

558

FTB-700G/800 Series

Start/Stop|TX Button

Start/Stop|TX Button

The

Start/Stop|TX

button allows to manually start or stop any test as well

as to enable traffic generation (Traffic Gen & Mon).

To start the test:

Tap the

Start

button to start the test.

Start

is available when the test is

not running.

To stop the test:

Tap the

Stop

button to stop the test; the traffic generation (Traffic Gen

& Mon) also stops if it was enabled (TX button).

Stop

is available when

the test is running.

By default, a message is displayed when the test stops asking to
generate a report. To disable this feature, see

Turn on Report

Generation

on page 549. Nothing prevents the configuration and

alarm/error injection setup while the test has been stopped; thus, if a
report is required, it should be saved before changing any test
parameters to avoid discrepancy between the configuration and
results. See

Report Button

on page 547 to generate and save a report

file.

To enable traffic generation (available with Traffic Gen & Mon):

Tap the

TX

button to enable traffic generation for all enabled streams;

the test is also started if it was not running. While the test is running the

TX

button is available to enable/disable traffic generation. Some

conditions, such as ARP not resolved, link down, etc., may prevent the
stream to be transmitted.

«
...
568
569
570
571
572
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды