manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 496

Test Functions

484

FTB-700G/800 Series

OH - OTN

JC

, column 16, OPU OH:  

Bits 1-6, Reserved (RES), are configurable from binary 

000000

 

(default) to 

111111

.

Bits 7-8, Justification Control (JC), are configurable from binary 

00

(default) to 

11

. Not available with ODU mux. Changing the JC 

value will corrupt the payload.

Row 3

TCM3/TCM2/TCM1

, columns 1-9, ODU OH: See 

TCM6/TCM5/TCM4

 on 

page 483 for more information. 

PM

, column 10-12, ODU OH: The Path Monitoring overhead contains 

the following bytes. 

The first PM byte (column 10) contains the TTI byte that is not 
configurable.

The second PM byte (column 11) contains the BIP-8 byte and is 
automatically generated for each frame. This byte is not configurable.

The third PM byte (column 12) contains the following sub-fields. This 
byte is configurable from 

00

 to 

FF

. The default value is 

01

.

EXP

., column 13-14, ODU OH: The two Experimental overhead bytes 

are configurable form 

00

 (default for each byte) to 

FF

. 

RES

, column 15, ODU OH: The Reserved (RES) bytes are configurable 

from 

00

 (default) to 

FF

.  

Bit 1-4

Bit 5

Bit 6-8

BEI

BDI

STAT

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды