manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 472

Test Functions

460

FTB-700G/800 Series

FDL - Bit-Oriented Message

FDL - Bit-Oriented Message 

Allows to set and configure the Bit-Oriented Messages (BOM) of the 
Extended Super-Frame (ESF). 

Note:

FDL is only available for DS1 interface with ESF framing. For Dual RX test, 
FDL is only available for the DS1 TX/RX port 1.

From the

 Test

 menu, tap 

Functions

, 

FDL

, and the 

Bit-Oriented Message 

tab. 

Generated Messages 

Priority 

Codeword

: The Bit-Oriented Message codewords are priority 

messages sent over the Data-Link. These messages are mostly used for 
networking operation and maintenance. A Bit-Oriented Message 
consists of 8 consecutive ones followed by a byte starting and ending 
by zeros. 

Injects

 generates the selected codeword priority message. 

Command/Response 

Amount

 allows the selection of the number of message to be 

generated. Choices are 

1

 to 

15

. The default value is 

10

. 

Inject

 manually generates the selected amount of messages.

Codeword

Pattern

RAI

00000000 11111111

Loopback Retention and Acknowledge

00101010 11111111

RAI-CI

00111110 11111111

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды