EXFO FTB-1 Скачать руководство пользователя страница 463 | Manualshive

Страница: 463 / 675

EXFO FTB-1 Скачать руководство пользователя страница 463

Test Results

NetBlazer

451

Traffic - OAM, S-OAM, and MPLS-TP OAM

Traffic - OAM, S-OAM, and MPLS-TP OAM

From the

Test

menu, tap

Results

,

Traffic

, and the

OAM

,

S-OAM

, or

MPLS-TP OAM

tab.

Traffic Monitoring

Note:

Only available with

Carrier Ethernet OAM

test application.



In TX, reports counts of CCM, LBM, LTM, DMM, LMM, SLM, TST, AIS,
LCK, and CSF frames transmitted. LTM and SLM are only available with
Ethernet OAM. Total count is reported as well as unicast and/or
multicast frame counts when applicable.



In RX, reports counts of CCM, LBR, LTR, DMR, LMR, SLR, TST AIS, LCK,
and CSF frames (LTR and SLR are only available with Ethernet OAM)
received regardless of the sender as long as the following criteria are
met:



S-OAM

: The destination MAC address matches either the local MEP

Unicast MAC address or a Multicast class 1 or class 2 address; and
the VLANs matches the unit port VLANs. Refer to

Unicast/Multicast

Addresses for Ethernet OAM

on page 638 for more information.



MPLS-TP OAM

: The destination MAC address matches either the

unit MAC address, FF:FF:FF:FF:FF:FF, or 01:00:5E:90:00:00; the
VLANs matches the unit port VLANs; and MPL Labels matches the
local MPLS Label Stack configuration. For AIS, LCK, and CSF, valid
messages must also have the MEG Level matching the Local MEG
Level.

Total count is reported as well as unicast and/or multicast frame counts
when applicable.

«
...
461
462
463
464
465
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды