manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 446

Test Results

434

FTB-700G/800 Series

Summary (S-OAM and MPLS-TP OAM)

RX Line Utilization

 meter and value, available with 

Loopback

 

function, indicate the line rate utilization percentage (only LBR frames 
are considered) received in the last second. 

TST RX

 

Rate

 meter and value, available with 

Test

 function, indicate the 

quantity of TST frames received in the last second. 

Frame Delay

 meter and value, available with 

Frame Delay

 function, 

indicate the average of the measured frame delays in the last second. 

Frame Loss Ratio

 meter, available with 

Frame Loss

 function, 

indicates for both Near-End and Far-End the last measured frame loss 
ratio in the last second. 

Synthetic Loss Ratio

 meter, available with 

Synthetic Loss

 function 

which is available with Ethernet OAM, indicates for both Near-End and 
Far-End the last measured Synthetic Loss ratio in the last second. 

Note:

Refer to 

S-OAM and MPLS-TP OAM

 on page 379 for more 

alarms/errors/statistics information. 

Summary 

Refer to 

S-OAM and MPLS-TP OAM

 on page 379 for more information on 

alarms. 

Thresholds 

Refer to 

Thresholds

 on page 222 for more information. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды