manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 443

Test Results

NetBlazer

431

Summary (S-OAM and MPLS-TP OAM)

Continuity Check (Peer MEP) 

Status

 displays the status of the continuity check with the peer MEP. 

TX CCM

 indicates the count of transmitted CCM frames. 

RX CCM

 indicates the count of valid CCM frames received. A valid 

frame for S-OAM has its source MAC address matching the Peer MEP 
MAC address; destination MAC address matching either the unit port 
Unicast MAC address or a Multicast class 1 address (refer to 638); and 
VLANs matching the unit port VLANs. A valid frame for MPLS-TP OAM 
has its destination MAC address matching either the unit MAC address, 
FF:FF:FF:FF:FF:FF, or 01:00:5E:90:00:00; VLANs matching the unit port 
VLANs; and MPL Labels matching the local MPLS Label Stack 
configuration. 

Status

Description

Loss Continuity

Loss of Continuity alarm is active. 

Mismerge

Mismerge alarm is active. 

Unexpected MEG Level  Unexpected MEG Level alarm is active. 

Unexpected MEP 

Unexpected MEP alarm is active. 

Unexpected Period 

Unexpected Period alarm is active. 

Unexpected MD Level 

Unexpected MD Level alarm is active. 

Receiving CCMs

CCM frames from the peer MEP are received without alarms. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды