manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 363

Test Results

NetBlazer

351

Graph (RFC 2544)

Graph (RFC 2544)

Displays the graph showing the 

Throughput

, 

Back-to-Back

, 

Frame Loss

, 

and 

Latency

 measurements. For 

Dual Test Set

 the graph shows results 

from 

Local to Remote

 and 

Remote to Local

 using distinctive colors. 

From the

 Test

 menu, tap 

Results

, and the 

Graphs

 tab. 

All

 button allows to view the graphs of all subtests simultaneously. 

Throughput

, 

Back-to-Back

, 

Frame Loss

, and 

Latency

 buttons allow to 

view an enlarged graph view of the selected subtest. 

Displayed Results

 allows to select the displayed results mode, either 

Minimum

, 

Maximum

 (default), 

Average

, or 

Current

. 

Step

, available with Frame Loss, allows to select the result step 

(100 percent by default) to be displayed. 

The X axis shows the frame sizes while the Y axis shows the subtest 
results.

Frame Size (Bytes)

 and 

Step (%)

, available with Frame Loss, allows to 

select either 

Frame Size

 (default) or 

Step

 as the X axis criterion. 

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды