manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 249

Test Setup - Test Configurator, Timer, and System

NetBlazer

237

Services - Profile

Test Parameters

Note:

Unit selection is available from the 

SLA Parameters

 on page 238.

For 

Dual Test Set

, parameters are configurable for both local to remote 

(

L->R

) and remote to local (

R->L

) directions. 

Traffic Policing

 check box when selected (default) allows to stress the 

rate limiting of the network by sending traffic at higher rate than 
committed by the SLA. 

Burst Max Rate

 allows to set the rate that is used for the CBS and EBS 

burst tests. Only available when the 

Burst Test

 is enabled (see 

EtherSAM - Global

 on page 137). 

Note:

Changing a criteria value (CIR, CIR+EIR, Ramp Traffic Policing, or Burst 
Max Rate) may affect the other criteria values in order to comply to the 
following rules:
CIR

CIR+EIR

Ramp Traffic Policing Rate

Line Rate

CIR

CIR+EIR

Burst Max Rate

Line Rate

However, make sure that the criteria values comply to the following rule 
with an adequate margin, as per ITU-T Y.1564 standard, for a burst test to 
be valid:
CIR

CIR+EIR

Burst Max Rate

Line Rate

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды