EXFO FTB-1 Скачать руководство пользователя страница 145 | Manualshive

Страница: 145 / 675

EXFO FTB-1 Скачать руководство пользователя страница 145

Test Setup - Test Configurator, Timer, and System

NetBlazer

133

EtherBERT, FC BERT, BERT (CPRI), and Unframed BERT

Shaping



TX Rate

allows the selection of the transmission rate in percentage of

utilization (100 percent by default), Mbit/s, Gbit/s, Frame/s, or IFG for
Ethernet; Mbit/s, Gbit/s, MB/s, or % for Fibre Channel. For Ethernet, the
maximum percentage is 105 percent

depending on the frame size

selected.



Enable TX

check box is automatically selected when starting the test

allowing stream generation; automatically cleared when the test stops.
The

Enable TX

check box may also be selected or cleared while the

test is running. Not available for FC BERT.

«
...
143
144
145
146
147
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды