manualshive.com logo in svg

EXFO FTB-1, Руководство пользователя

Поделиться
Скачать
EXFO FTB-1 Скачать руководство пользователя страница 140

Test Setup - Test Configurator, Timer, and System

128

FTB-700G/800 Series

Clock

Ext Clock Out

Note:

Available when the 

Clock Mode

 is set to 

Internal

, or 

Recovered

.  

Allows to set the clock that will be generated.

Interface Type

 allows the selection of the clock interface: 

DS1

(default), 

E1

, and 

2MHz

. 

Ext Clock Out

 on a green background indicates that a valid clock is 

generated on the 

EXT CLK

port.

LOC

 on a red background indicates that no clock is generated on the 

EXT CLK

port.

LBO

 (Line Build Out), available with DS1 only, allows the selection of 

the interface Line Build Out that meets the interface requirements over 
the full range of cable lengths: 

DSX-1 (0-133 ft)

 (default), 

DSX-1 (133-266 ft)

, 

DSX-1 (266-399 ft)

, 

DSX-1 (399-533 ft)

, and 

DSX-1 (533-655 ft)

. 

Line Coding

, available with DS1 and E1, allows the selection of the 

interface line coding. 

For DS1: 

AMI

 and 

B8ZS

 (default). 

For E1: 

AMI

 and 

HDB3

 (default). 

Framing

, available with DS1 and E1, allows the selection of the 

interface framing. 

For DS1: 

SF

, 

SLC-96

, and 

ESF 

(default).

For E1: 

PCM30

 (default), 

PCM30 CRC-4

, 

PCM31

, and 

PCM31 CRC-4

.

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды