EXFO FTB-1 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 675

EXFO FTB-1 Скачать руководство пользователя страница 131

Test Setup - Test Configurator, Timer, and System

NetBlazer

119

BERT



Invert

check box, when selected (cleared by default), inverts the test

pattern meaning that every 0 will be changed for 1 and every 1 for 0.
For example, the pattern 1100 will be sent as 0011. Not available when
pattern is Multi-Pattern.

Bit Error



Pass/Fail Verdict

allows to enable bit-error-rate pass/fail verdict by

selecting either

Bit Error Count

or

Bit Error Rate

. The default value is

Disabled

.



BER Threshold

allows to enter the threshold

Count

or

Rate

value that

will be used to declare the pass/fail verdict. The

BER Threshold

applies to individual pattern for

Multi-Pattern

.

For

Count

, enter the maximum bit error count allowed before

declaring a fail verdict:

0

(default) to

999999

.

For

Rate

, enter the maximum bit error rate allowed before declaring a

fail verdict:

1.0E-14

to

1.9E-01

. The default value is

1.0E-12

.

«
...
129
130
131
132
133
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды