EXFO FTB-1 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 675

EXFO FTB-1 Скачать руководство пользователя страница 104

Test Setup - Test Configurator, Timer, and System

92

FTB-700G/800 Series

Test Configurator Overview

Test Configurator Overview

The

Test Configurator

tab displays the interconnected blocks composing

the test structure. Each block of the test structure gives an overview of its
configuration/status. Availability of each block depends on the selected test
application and its structure. Arrows are used to indicate the
interconnection between blocks as well as the direction of the clock and
data flow. Tap on a block to change the configuration parameters of this
block.

From the

Test

menu, tap

Setup

, and the

Test Configurator

tab.



Intelligent Apps:

The block arrangement represents the network under test. From any
block, either select the basic parameters or click on

More

for all

settings.



Local

block displays and allows to change basic interface settings.

Tap on the

More

button to access all settings.



Network

block displays and allows to change basic test settings.

Tap on the

More

button to access all settings.

Remote
Operation Mode

Remote Block

Local Block

Network Block

«
...
102
103
104
105
106
...
»

Содержание FTB-1




































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды