EXFO bv10 Скачать руководство пользователя страница 70

Страница: 70 / 116

CLI Command Reference

BV10

Configuration Commands

interface lan|test speed auto

Description

Auto-negotiates all supported LAN (10/100) or Test (10/100/1000 for

electrical or 1000 for optical) port speeds.
This command cannot be sent through the Test port.

Syntax

interface lan|test speed auto

Example

bv10-100>

interface lan speed auto

interface test speed 10|100|1000 auto

Description

Auto-negotiates the specified electrical TEST port speed (10/100/1000).
This command cannot be sent through the Test port.

Syntax

interface test speed 10|100|1000 auto

Example

bv10-100>

interface test speed 100 auto

interface test speed 10|100|1000 force

Description

Forces the electrical TEST port speed (10/100/1000) to the specified

value; no auto-negotiation is performed.
This command cannot be sent through the Test port.

Syntax

interface test speed 10|100|1000 force

Example

bv10-100>

interface test speed 1000 force

Содержание bv10





















































































































Результаты поиска

Содержание bv10

Отзывы:

EXFO bv10, Руководство пользователя, Страница: 70 / 116

Результаты поиска

Содержание bv10

Отзывы: