exemys GRD-MQ Series Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 85

background image

If the LED blinks rapidly a few seconds (2 or 3) and then blinks slowly verify:

That the IP address and port to which the GRD is attempting to connect are the
correct ones.
That there is no reason why the server is rejecting the connection request (ex.
That is requesting identification or authentication).

A connection is established and then it closes

Verify that there is no reason why the server is rejecting the connection request
(ex. That is requesting identification or authentication).

The connection is established but the communication fails

If the Link LED remains constantly on and it does not blink, is indicating that there is
no data reception or transmission. If the Link LED blinks sporadically, it is indicating
that data are being sent and/or received. In any case verify:

That the established broker connection was made to the correct IP address and
port (through SMS with the ‘

state

’ command).

For more information on troubleshooting problems please contact

[email protected]

2020-09-28

GRD-MQ User Manual

Troubleshooting

84 / 84

«
...
83
84
85

Содержание GRD-MQ Series






















































































Отзывы:

Нет отзывов

Похожие инструкции для GRD-MQ Series

Бренд: Campbell Страницы: 86

Бренд: Racelogic Страницы: 9

Memorator R SemiPro

Бренд: Kvaser Страницы: 33

Бренд: Datafox Страницы: 157

Бренд: ete Страницы: 6

Isolated Analog Input Device NI PXI-4224

Бренд: National Instruments Страницы: 85

Бренд: Fluke Страницы: 72

Бренд: Fluke Страницы: 72

Бренд: LUDLUM Страницы: 72

MIR 6000 Series

Бренд: Tamam tadbir Страницы: 27

Бренд: MadgeTech Страницы: 12

Бренд: Dickson Страницы: 2

Бренд: Evikon Страницы: 18

Бренд: Marathon Страницы: 7

Бренд: Wildlife computers Страницы: 9

Бренд: Campbell Страницы: 32

Бренд: WEBTEC Страницы: 336

Бренд: VOLTCRAFT Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды