exemys GRD-MQ Series Скачать руководство пользователя страница 59

Страница: 59 / 85

MQTTPSSX

pssx

MQTT password continuation

Disconnecting the GRD

Command

Description

DISC

[password]

This command disconnects the GRD-MQ from the broker preventing a
reconnection until the connection is reconfigured.

Modifying the password

Command

Description

PASSW

newpassword [password]

Modifies the password used by the GRDs for SMS and the
connection to the broker

The password can have a maximum of 8 characters and is not case sensitive.

Configuring a new password if you did not have any:

PASSW

newpassword

Configuring a new password if you already have one:

PASSW

newpassword previouspassword

Erasing the password:

To leave the equipment without a password you must send a message leaving 2 spaces between the
command and the previous password.
PASSW previous

password

Rebooting the GRD-MQ

Command

Description

RESET

[password]

Reboots the GRD-MQ

Reading Inputs and Outputs

It's possible to read the value of the channels by SMS

Digital Inputs:

Command

Description

GETI

[

channel]

Reads channel

(Read note*)

GETI

[first

channel]…[last

channel]

Read several

channels

GRD-MQ User Manual

SMS Monitoring and Configuration

58 / 84

Содержание GRD-MQ Series






















































































Результаты поиска

Содержание GRD-MQ Series

Отзывы:

Похожие инструкции для GRD-MQ Series

Бренды по названию

Популярные бренды

exemys GRD-MQ Series, Руководство пользователя

Результаты поиска

Содержание GRD-MQ Series

Отзывы:

Похожие инструкции для GRD-MQ Series

Бренды по названию

Популярные бренды