Exegin Q53 Скачать руководство пользователя страница 62

Страница: 62 / 84

Q53 Installation and Configuration Guide © Exegin Technologies Limited, 2009

viii. Reference Information
Complete Command Reference

Miscellaneous commands

These commands do not fall under any specific section of the command line interface
shell but they are used quite frequently.

store net mask netmask

Store the subnet mask for the Q53.

For example:

store tcpip 1 mask

255.255.255.0

store net opts[[-]dhcp]

Enable or disable the automatic DHCP
requests for IP addresses upon bootup.
Prefix the ‘DHCP’ option with a dash (‘-’) to
disable the option; otherwise it is enabled.

For example:

store tcpip 1 opts -dhcp

store net rxbuf packets

Determine the receive window size for the
Q53. Usually the

packets

value ranges from

2-8 with the lower number allowing for
more simultaneous TCP connections with
the Zigbee gateway bridge device.

For example:

store net rxbuf 2

store zbnwk opts [-]edscan

Enable/disable power-up energy scan on the
Zigbee radios.

store zbmac freqband [[-]868]

[[-]915] [[-]2400]

Sets the freqency band for each Zigbee
radio.

store zipt port portnumber

Sets the UDP port number to be used for
bridging Zigbee traffic over the IP network.
The default port number is 17755.

Table 7—Miscellaneous Commands

Command Syntax

Description

close <sd>|all

Close the network connection defined by the
socket descriptor. Socket descriptors can be
obtained using the

netstat

command.

If the argument

all

is entered, then all

active network connections will be
terminated, including the telnet session in
which the command was entered.

Table 6—Store Command Options

Command Syntax

Description

Содержание Q53





















































































Результаты поиска

Содержание Q53

Отзывы:

Похожие инструкции для Q53

Бренды по названию

Популярные бренды

Exegin Q53, Руководство по установке и настройке

Результаты поиска

Содержание Q53

Отзывы:

Похожие инструкции для Q53

Бренды по названию

Популярные бренды