Page - 21
Remote Panic Feature
Should you feel threatened or the need to attract attention at any time, you can activate
your Excalibur Gold's Remote Panic feature by depressing the large transmitter button for 3
seconds. Your system will respond by sounding the siren (or horn), locking the doors and
flashing the exterior lights for 60 seconds. Remote Panic may operated regardless of the
system's armed or disarmed status, while the ignition switch is "on", and while the system is
in Valet Mode. To disengage Remote Panic, simply press and release the large transmitter
button again. If you should wish to enter your vehicle after engaging Remote Panic, press and
release the large transmitter to disengage Remote Panic; the doors will also unlock, allowing
easier entry.
Optional Trunk Release: If your vehicle is equipped with electric trunk release, your
authorized Excalibur Gold dealer can configure your system to accomplish trunk release from
your transmitter. To operate this option when equipped, simply press and hold the small center
transmitter button for 2 seconds. Your vehicle will respond by releasing the trunk lid, chirping
the siren twice (or honking the horn twice), disarming the system and turning on your exterior
and interior lights for 30 seconds. The trunk release output will not operate with the ignition
switch "on" unless the vehicle's door is open. If desired, your Excalibur Gold dealer can
program the security system to remain armed when this feature is used.
Trunk Release And 3rd Channel Output
Page - 22
Optional 3rd Channel Output: This output's operation is the same as the trunk release
output except for the following items: Press the lower small transmitter button for 2 seconds
to activate the 3rd channel output. The 3rd channel output will operate regardless of the
ignition switch being "on" or "off", and there is no audible or visual confirmation. This output
may be used to operate optional equipment such as remote car starters or window roll-up
modules.
The Visual Deterrent LED is a visual indicator of what state the security system is in at any
given time. It is located on the top of the Information and Programming Module. There are 16
conditions that are reflected by the Visual Deterrent LED:
1) Off
= The security system is disarmed and not performing any automatic
functions.
2) On Constant
= The security system is in the Valet Mode.
3) Flashing Slow
= The security system is Fully Armed.
4) Flashing Fast
= The 3 second Arming Delay, the 30 second Last Door Arming
feature or 90 second Automatic Rearming feature is in progress.
Automatic Transmitter Verification
TM
: After the ignition is turned "on", the Visual
Deterrent LED will flash to indicate the number of transmitters programmed to operate your
security system. For example: two flashes between pauses indicates that only two transmitters
are coded to operate your system. Whenever you leave your vehicle and keys
with someone, you will now have the peace of mind of knowing that only your transmitters
Visual Deterrent LED
Page - 23
will operate the security system and that no additional transmitters have been coded into your
system for the purpose of stealing your vehicle. This feature works for 10 seconds every time
the ignition switch is turned "on".
5) Flash-1x & Pause = 1 transmitter code is stored in the system's memory.
6) Flash-2x & Pause = 2 transmitter codes are stored in the system's memory.
7) Flash-3x & Pause = 3 transmitter codes are stored in the system's memory.
8) Flash-4x & Pause = 4 transmitter codes are stored in the system's memory.
Zone Violation: If the system is activated the Red Visual Deterrent LED will start to flash
and pause the #9 through #12 sequences to indicate which protected circuit caused the
activation. This is seen while the system is activated and after disarming, until the ignition
switch is turned "on", which will clear the security system's memory. The system's memory
circuit can store four different codes, and if multiple violations involving different zones
occurred, the different zones will be shown.
9) Flash-2x & Pause
= System was activated from the hood or trunk circuit wire.
10) Flash-3x & Pause
= System was activated from the door circuit wire.
11) Flash-4x & Pause
= System was activated from the auxiliary input.
12) Flash-5x & Pause
= System's prewarn feature was activated.
Zone Testing: Every time the ignition key is turned off , the Visual Deterrent LED will flash
and pause the #13 through #16 code to indicate if a protected circuit, or "zone", is in an activated
state. For example: open a door after the ignition is turned off and the Red Visual
Deterrent LED will start flashing 3 times and pause until the door is closed. If another
protected entry point is violated while the door is still open, then the Red Visual Deterrent LED
will alternate flashing both zone violation codes.
13) Flash-2x & Pause
= System is detecting a trigger from the hood or trunk circuit.
14) Flash-3x & Pause
= System is detecting a trigger from the door circuit wire.
15) Flash-4x & Pause
= System is detecting a trigger from the auxiliary input.
16) Flash-5x & Pause
= System is detecting a trigger from the prewarn input.
The Digital Status Indicator is found on Information and Programming Module and
provides more direct system status information the user. This information is displayed in the
form of letters, numbers and symbols. Unlike the Visual Deterrent LED, these displays last,
for most applications, for a shorter period of time. Please note that the Digital Status Indicator
does has no display when driving after display periods, or after timing out upon arming the
system.
1) Display shows
for 30 seconds after the ignition has been turned "off" indicates that
the security system is in the Valet Mode.
2) Display shows
for 10 seconds after the following display indicates that the security
system is Fully Armed.
3) Display shows
indicates that the 3 second Arming Delay, the 30 second Last Door
Arming feature or 90 second Automatic Rearming feature is in progress.
Page - 24
Digital Status Indicator
