manualshive.com logo in svg

Exalt EX-4.5r GigE, Руководство по установке и управлению

Поделиться
Скачать
Exalt EX-4.5r GigE Скачать руководство пользователя страница 104

Exalt Installation and Management Guide

EX-r Series GigE Digital Microwave Radios

96

201872-004

2016-05-26

Europe and ITU Country Compliance

All of these permitted devices must be professionally installed. They can only be used as a point-to-
point transmission device for fixed or temporary-fixed (non-mobile) installations.

The EX-5r GigE product family operates under EN 301 893 and EN 302 502 rules as a license-exempt 
device. 

The EX-5r GigE product family complies with ETS 301 893 for the 5.3 and 5.47 GHz bands for 
license-exempt use for most countries recognizing ETSI or ITU band assignments. This band is not yet 
harmonized for all countries recognizing ETSI or ITU band assignments. These bands require 
Dynamic Frequency Selection (DFS) and Transmitter Power Control (TPC) for radar-detection and 
avoidance. There is a +30dBm EIRP limit applied to this band. Transmitter power must be adjusted 
accordingly with respect to the RF cabling losses and antenna gains associated with each terminal.

The EX-5r GigE product family complies with ETS 302 502 for the 5.8 GHz band. This band is not yet 
harmonized for all countries recognizing ETSI or ITU band assignments. Consult the individual 
country regulations or your Exalt Wireless representative for details. This band requires DFS and TPC 
for radar-detection and avoidance. There is a +33dBm EIRP limit for use of the 10 MHz BW setting, 
and a +36dBm EIRP limit for use of the 20 MHz BW setting. Some countries limit the EIRP to +5dBm 
for all bandwidths in this band.

All models comply with the requirements for CE Mark (EN 60950-1 and IEC 60950-1) and EMC (EN 
301 489-17). No substitutions shall be made, and all wiring and grounding instructions contained in 
this manual must be followed to ensure safety in accordance to the standards and local rules.

Note: 

Do not use external amplifiers to boost the power or overcome transmission system 

losses, unless the specific amplifier/cable/antenna combination has expressly been 
authorized by the specific country regulations. The output power must never exceed that 
specified in 

Specifications

.

Содержание EX-4.5r GigE





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды