manualshive.com logo in svg

Exabyte VXA-2 AUTOPAK1X7, Руководство по эксплуатации продукта, Страница: 98 / 104

Поделиться
Скачать
Exabyte VXA-2 AUTOPAK1X7 Скачать руководство пользователя страница 98

90

P

RODUCT

 M

ANUAL

 

1010964

Appendix

 A—S

PECIFICATIONS

S

AFETY

 

AND

 R

EGULATORY

 A

GENCY

 C

OMPLIANCE

This section describes the autoloader’s compliance with safety and regulatory 

agency standards.

S

AFETY

 A

GENCY

 S

TANDARDS

The autoloader complies with and is certified to the applicable requirements of 

the following domestic and international product safety standards:

!

UL Standard 1950, 3rd Edition, Information Technology Equipment 

including Electrical Business Equipment

!

CSA Standard C22.2 No. 950-95, Safety of Information Technology 

Equipment including Electrical Business Equipment

!

EN 60950:2000, Safety of Information Technology Equipment including 

Electrical Business Equipment

R

ADIATED

 

AND

 C

ONDUCTED

 R

ADIO

 F

REQUENCY

 E

MISSIONS

 (EMI)

The autoloader meets the requirements for radiated and conducted emissions 

as defined by the following standards:

!

FCC Rules and Regulations, Part 15, Class B:  Radio Frequency Devices, 

Subpart B:  Unintentional Radiators

!

Industry Canada Notice, ICES-003, Class B, Digital Apparatus

!

CISPR Publication 22, 1987 (EN 55022), Class B

!

VCCI Class 2 (Japan)

Important

To comply with the following regulations and standards, you 

must use shielded cables and provide adequate grounding of 

the SCSI bus and the input power when installing the 

autoloader in an office or industrial environment.

Important

According to FCC regulations, changes or modifications to the 

autoloader that are not expressly approved by Exabyte may 

void the user’s authority to operate the autoloader.

Содержание VXA-2 AUTOPAK1X7









































































































Отзывы:

Нет отзывов