EWM T5.00 Скачать руководство пользователя страница 48

Страница: 48 / 81

Functional characteristics

Welding programs

099-00T500-EW501

2.9.2022

Function

Operation

Mode

Welding current On / Off

BRT 1

Secondary current (in latched operation)

BRT 2

Infinitely variable increase of welding current (up/down speed)

Infinitely variable decrease of welding current (up/down speed)

DOWN

Switching between up/down speed and JOB number

BRT 2

Increase JOB number

Decrease JOB number

DOWN

Gas test

BRT 2

3 s

5.2.10.2 Tapping function (tap torch trigger)

Tapping function: Swiftly tap the torch trigger to change the function. The set torch mode determines the

operating mode.
The tapping function can be selected separately for each torch mode for the start of welding with parame-

ter

and for the end of welding with parameter

. If parameter

is activated, there is no need to

tap the secondary current.

5.2.10.3 Up/down speed

Functionality

Press and hold the up push-button:

Increase current up to the maximum value (main current) set in the power source.

Press and hold the down push-button:

Decrease current to the minimum value.
Use the machine configuration menu

> see 5.11 chapter

to set the up/down speed parameter

which

determines the speed with which a current change becomes effective.

5.2.10.4 Current jump

By tapping the corresponding torch trigger the welding current can be determined in an adjustable jump

range. Each tap will cause the welding current to jump up or down by the defined value.

The “current jump” parameter

is set in the machine configuration menu

> see 5.11 chapter

Содержание T5.00


















































































Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды

EWM T5.00, Руководство по эксплуатации

Результаты поиска

Содержание T5.00

Отзывы:

Похожие инструкции для T5.00

Бренды по названию

Популярные бренды