EWM Picomig 305 Synergic TKM Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 75

background image

Design and function

MIG/MAG welding

36

099-005640-EW501

04.06.2020

A prerequisite for the automatic inching process is the correct preparation of the wire guide,

especially in the capillary and wire guide tube area

> see 5.2.1 chapter

.

• The contact pressure has to be adjusted separately for each side (wire inlet/outlet) at the feed roll ten-

sioner setting nuts depending on the welding consumable used. A table with the setting values can be

found on a sticker near the wire drive.

Version 1: left hand mounting

Version 2: right hand mounting

Figure 5-18

Automatic inching stop

Touch the welding torch against the workpiece during inching. Inching of the welding wire will stop as

soon it touches the workpiece.

5.2.4.4 Spool brake setting

Figure 5-19

Item Symbol Description

0

1

Allen screw

Securing the wire spool retainer and adjustment of the spool brake

• Tighten the Allen screw (8 mm) in the clockwise direction to increase the braking effect.

Tighten the spool brake until the wire spool no longer turns when the wire feed motor stops but

without it jamming during operation!

5.2.5 Definition of MIG/MAG welding tasks

This machine range features simple operation with a very wide range of functions.
• JOBs (welding tasks consisting of welding process, type of material, wire diameter and type of shiel-

ding gas) are pre-defined for all common welding tasks.

• Simple JOB selection from a list of pre-defined JOBs (sticker on the machine).
• The required process parameters are calculated by the system depending on the operating point spe-

cified (single-dial operation via wire speed rotary dial).

• Conventional welding task definition using wire speed and welding voltage is also possible.

The welding task definition described below applies when defining MIG/MAG and cored wire

welding tasks.

Pay attention to the signal light for the polarity setting!

It may be necessary to change the welding current polarity depending on the JOB selected or the

welding process.
• Reconnect the polarity selction plug if necessary.

«
...
34
35
36
37
38
...
»

Содержание Picomig 305 Synergic TKM












































































Отзывы:

Нет отзывов

Похожие инструкции для Picomig 305 Synergic TKM

Бренд: Eclipse Страницы: 48

Бренд: Eclipse Страницы: 52

Бренд: Eclipse Страницы: 48

Бренд: ECO Schulte Страницы: 18

FSA ECO SR-EFR BG

Бренд: Eco Страницы: 23

Бренд: Laars Страницы: 14

Бренд: S&P Страницы: 72

Бренд: AmeriWater Страницы: 16

Бренд: Abicor Binzel Страницы: 2

Бренд: Magnavox Страницы: 23

Blue Thunder Series

Бренд: Miller Страницы: 36

Бренд: Onkyo Страницы: 9

Бренд: Behringer Страницы: 20

Бренд: American Audio Lab Страницы: 31

Бренд: Kogan Страницы: 16

Бренд: Overhead door Страницы: 52

Бренд: MAGNAWELD Страницы: 18

Бренд: VAC-CON Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды