Design and function
Definition of MIG/MAG welding tasks
099-005366-EW501
31.07.2014
53
5.16.4.1 Operating mode
This parameter setting is specified by the robot control via the RINTX12 or BUSINTX11 robot interface
(see documentation in the relevant interface description).
The selected parameter is displayed on the status displays on the control panel.
5.16.5 Welding type
This parameter setting is specified by the robot control via the RINTX12 or BUSINTX11 robot interface
(see documentation in the relevant interface description).
The selected parameter is displayed on the status displays on the control panel.
NOTE
This parameter can be changed over during the welding process.
5.16.5.1 Program or control voltage mode
NOTE
The operating point can either be specified using up to 15 freely definable programs
(PROG 1 to PROG 15) or an operating point can be set using control voltages (PROG 0)
via the robot interface (RINTX11 / BUSINTX10).
Different welding tasks or positions on a workpiece demand various welding outputs (operating points) or
welding programs.
For each program, the
•
Wire speed
•
Correction of the arc length and the
•
Dynamics / choke effect
can be set separately.
15 different programs (PROG 1 to PROG 15) can be defined. It is possible to switch between these
programs during the welding process.
The parameters for the relevant program are selected on the control panel.
Operating
element
Action
Result
Display
X x
Select "Program number"
The signal light displays the selection.
PROG 1 to PROG 15 are available.
P1 DV2 : 2.0m/m
1 x
Select "Wire speed"
The signal light displays the selection (m/min).
P1 DV2 : x.x m/m
n x
Select "Wire speed"
Setting from 0.1 to 40.0 m/min.
P1 DV2 : x.x m/m
1 x
Select "Voltage correction"
The signal light displays the selection (V).
P1 U2 : + x.x V
n x
Select "Voltage correction"
Setting from -9.9 V to +9.9 V.
P1 U2 : + x.x V
1 x
Press "Dynamics"
The signal light (DYN) flashes.
Содержание alpha Q 352 puls MM
