manualshive.com logo in svg

Evolution 052-0001, Оригинальное руководство пользователя, Страница: 87 / 91

Поделиться
Скачать
Evolution 052-0001 Скачать руководство пользователя страница 87

completely covering the blade teeth, and the 
cutting head locked in the upper position, 
before releasing the Cutting Handle.

WARNING: Never pull the cutting head and 
spinning blade towards you when making a 
sliding cut. The blade may try to climb up on 
top of the work-piece, causing the cutting 
head to ‘kickback’ forcefully. 
The cutting head should always be positioned 
as outlined above before attempting to make 
a sliding cut. When the cutting head is in the 
correct position above the work-piece it can 
be lowered and pushed rearwards towards 
the fence to complete the cut.

MITRE CUTTING (Fig. 58)

The rotary table of this machine can be turned 
through 50˚ to the left or right from the normal 
cross-cut (0˚) position.
Positive stops are provided at 45˚, 30˚, 22.5˚ and 
15˚ to both the right hand and left hand sides.
Mitre Cutting is possible with or without the 
sliding carriage system being deployed.

•  Loosen the mitre handle locking knob 

(Fig. 56) 

by turning the locking knob anti-clockwise.

•  Pull up the positive stop locking lever. 

(Fig. 57)

•  Turn the rotary table to the desired angle. 

Note: 

A protractor scale is incorporated into 

the machines base to aid setting.
•  Tighten the mitre handle locking knob when 

the angle is achieved. 

Note: 

It is good practice to tighten the Mitre 

Locking Knob even when a positive stop is 
selected and the Positive Stop Locking Lever is 
positively engaged. 

BEVEL CUTTING BY
TILTING THE CUTTING HEAD 

 

A bevel cut 

(Fig. 55)

 is made with the rotary table 

set at 0˚ mitre angle. 
 

Note:

 It may be necessary to adjust the upper 

section of the sliding fence to provide clearance 
for the moving cutting head. 

(Fig. 29-30)

The cutting head can be tilted from the normal 0˚ 
(perpendicular position) to a maximum angle of 
45˚ from the perpendicular to the left hand side 
only. Bevel cutting is possible with or without the 
sliding carriage system being deployed. 

Note: 

A positive stop is provided at 33.9˚ Bevel 

angle. This is accessed by deploying (pushing 
inwards) the 33.9˚ Bevel Pin. 

(Fig. 59)

 Normally 

the Bevel Pin should be left in the un-deployed 
(pulled out) position.

To tilt the cutting head to the left:

•  Loosen the bevel lock handle.

 (Fig. 60)

•  Tilt the cutting head to the required angle. 

A protractor scale is provided as an aid to 
setting. 

(Fig 61)

•   Tighten the bevel lock handle when the 

desired angle has been selected.

•  Stand to the left side of the Cutting Handle 

when making a cut.

When cutting is completed:
•  Release the ON/OFF trigger switch to switch 

off the motor, but keep your hands in position.

•  Allow the blade to come to a complete stop. 
•  Allow the cutting head has to rise to its 

upper position, with the lower blade guard 
completely deployed and covering the blade 
before removing yours hand(s).

•  Return the cutting head to the 

 perpendicular position.

COMPOUND CUTTING (Fig. 62)

A compound cut is a combination of a mitre  
and bevel cut employed simultaneously.  
When a compound cut is required, select the 
desired bevel and mitre positions as  
previously described.

Note: 

Compound Cutting with the sliding 

carriage system deployed is possible. 
Always check that the sliding blade does not 
interfere with the machines fence or any other 
parts of the machine. Adjust the upper left 
hand section of the sliding fence if necessary.

Place the saw on a secure stationary work 

surface and check the saw over carefully. 

Check particularly the operation of all the 
machines safety features before attempting  
to operate the machine.

PREPARING TO MAKE A CUT
DO NOT OVER-REACH

Keep good footing and balance. Stand to one 
side so that your face and body are out of line 
of a possible kickback. 

WARNING: Freehand cutting is a major cause 
of accidents and should not be attempted.

•  Ensure that the work-piece is always firmly 

resting against the fence, and where practical 
is clamped with the Hold Down Clamp to 
the table.

•  The saw table should be clean and free from 

any sawdust etc. before the work-piece is 
clamped into position.

•  Ensure that the ‘cut-off’ material is free to 

move sideways away from the blade when 
the cut is completed. Ensure that the ‘cut-off’ 
piece cannot become ‘jammed’ in any other 
part of the machine.

•  Do not use this saw to cut small pieces. If the 

work-piece being cut would cause your hand 
or fingers to be within 150mm of the saw 
blade, the work-piece is too small.

CHOP CUTTING

This type of cut is used mainly for cutting small or 
narrow section material. The cutting head is gently 
pushed down to cut through the work-piece.
The sliding carriage should be locked in its 
rearmost position. 

(Fig. 49)

•  Slide the cutting head to the rear as far as it 

will go.

•  Tighten the slide lock screw.

 (Fig. 50)

•  Place the work-piece on the table and  

against the fence and secure with clamp(s)  
as appropriate.

•  Grasp the Cutting Handle.
•  Turn the motor on and allow the saw blade 

to reach full speed.

•  Press the lower guard locking trigger to 

release the cutting head. 

(Fig. 51)

•  Lower the Cutting Handle downwards and 

cut through the work-piece.

•   Allow the speed of the blade to do the work, 

there is no need to apply undue pressure to 
the Cutting Handle.

•  When the cut has been completed, release 

the ON/OFF trigger switch.

•  Allow the blade to come to a complete stop.
•  Allow the cutting head to rise to its upper 

position, with the lower blade guard 
completely covering the blade teeth, and the 
cutting head locked in the upper position, 
before releasing the Cutting Handle.

•  Remove the work-piece.

SLIDE CUTTING

This saw is equipped with a sliding carriage 
system. Loosening the slide lock screw will 
release the slide and allow the cutting head to 
move forwards and backwards. 

(Fig. 52)

The saw blade is lowered into the work-piece 
and then pushed to the rear of the machine to 
complete a cut. This type of cut can be used for 
cutting wide pieces.

•  Position the work-piece on the table and 

against the fence and secure with clamp(s) as 
appropriate.

•  Loosen the slide lock screw.
•  Grasp the Cutting Handle and pull the 

cutting head forward until the arbor (centre 
of saw blade) is over the front edge of the 
work-piece. 

(Fig. 53)

•  Operate the ON/OFF motor trigger switch 

and allow the saw blade to reach full speed.

•   Press the lower blade guard locking trigger 

for cutting head release.

•  Push the Cutting Handle all the way down 

and cut through the leading edge of the 
work-piece.

•  Gently push the cutting handle rearwards 

towards the fence completing the cut.

•  Always push the cutting head to the full rear 

position during each cut. 

(Fig. 54)

•   When the cut has been completed, release 

the trigger switch and allow the blade to 
come to a complete stop.

•  Allow the cutting head to rise to its upper 

position, with the lower blade guard 

30

31

www.evolutionpowertools.com

www.evolutionpowertools.com

DE

EN

ES

FR

IT

PL

PT

RO

Содержание 052-0001




























































































Отзывы:

Нет отзывов