manualshive.com logo in svg

Evolution 052-0001, Оригинальное руководство пользователя, Страница: 77 / 91

Поделиться
Скачать
Evolution 052-0001 Скачать руководство пользователя страница 77

(3.7) 

SAFE OPERATION

Always ensure that you have selected the correct 
saw blade for the material being cut. 

Do not 

use 

this mitre saw to cut materials other than those 
specified in this Instruction Manual.

When transporting a mitre saw ensure that the 
cutting head is locked in the 90° down position  
(if a sliding mitre saw ensure that the slide bars are 
locked). Lift the machine by gripping the outer 
edges of the base with both hands (if a sliding 
mitre saw, transport using the handles provided). 
Under no circumstances shall the machine be 
lifted or transported using the retractable guard  
or any part of its operating mechanism.
Bystanders and other colleagues must be kept 
at a safe distance from this saw. Cut debris can, 
in some circumstances, be ejected forcibly 
from the machine, posing a safety hazard to 
people standing nearby.

Before each use check the operation of the 
retractable guard and its operating mechanism 
ensuring that there is no damage, and that all 
moving parts operate smoothly and correctly.
Keep the work bench and floor area clear of all 
debris including sawdust, chips and off-cuts.
Always check and ensure that the speed 
marked on the saw blade is at least equal to 
the no load speed marked on the mitre saw. 
Under no circumstances shall a saw blade be 
used that is marked with a speed that is less than 
the no-load speed marked on the mitre saw.
 
Where it is necessary to use spacer or 
reducing rings these must be suitable for the 
intended purpose and only as recommended 
by the manufacturer.

If the mitre saw is fitted with a laser it shall not 
be replaced with a different type. If the laser 
fails to operate it shall be repaired or replaced 
by the manufacturer or authorised agent. 
The saw blade shall only be replaced as 
detailed in this instruction manual.
Never attempt to retrieve off-cuts or any other 
part of the work-piece until the cutting head is 
in the raised position, the guard is fully closed 
and the saw blade has stopped rotating.

(3.8) 

PERFORM CUTS  

CORRECTLY & SAFELY

Wherever practicable always secure the  
work-piece to the saw table using the work 
clamp where provided.

Always ensure that before each cut the mitre 
saw is mounted in a stable position.

If needed the mitre saw can be mounted on 
a wooden base or work bench or attached to 
a mitre saw stand as detailed in this instruction 
manual. Long work-pieces should be 
supported on the work supports provided or 
on appropriate additional work supports.

(2.8) 

WARNING: The operation of any mitre 

saw can result in foreign objects being 
thrown towards your eyes, which could result 
in severe eye damage. Before beginning 
power tool operation, always wear safety 
goggles or safety glasses with side shield or a 
full face shield when needed. 

WARNING: If any parts are missing, do not 
operate your mitre saw until the missing 
parts are replaced. Failure to follow this rule 
could result in serious personal injury. 

(3.9)

ADDITIONAL SAFETY ADVICE

CARRYING YOUR MITRE SAW

WARNING: When using electric tools basic 
safety precautions should always be followed 
to reduce the risk of fire, electric shock and 
personal injury including the following. 

READ 

all these instructions before attempting to 

operate this product and save these instructions. 

Safety Advice:

•  Although compact, this mitre saw is heavy.  

To reduce the risk of back injury, get 
competent help whenever you have to lift 
the saw.

•  Hold the tool close to your body when lifting. 

Bending your knees so you can lift with your 
legs, not your back. Lift by using the cutting 
handle on the head of the mitre saw and 
the large, orange handle on the rear of the 
carriage slide.

•  Never carry the mitre saw by the power cord. 

Carrying the mitre saw by the power cord could 
cause damage to the insulation or the wire 
connections resulting in electric shock or fire.

•  Before moving the mitre saw tighten the 

mitre and bevel locking screws and the 
sliding carriage locking screw to guard 
against sudden unexpected movement.

•  Lock the cutting head in its lowest position. 

Ensure that the cutting head locking pin is 
completely engaged in its socket.

WARNING: Do not use the blade guard as 
a ‘lifting point’. The power cord must be 
removed from the power supply before 
attempting to move the machine. 

•  Lock the cutting head in the down position 

using the cutting head locking pin.

•  Loosen the Mitre Angle locking screw. Turn 

the table to either of its maximum settings. 

•  Lock the table in position using the  

locking screw.

•  Wrap the cable around the cable guide.

(4.1) 

GETTING STARTED - 

UNPACKING

WARNING: 

Due to the power input of this 

product on start up, voltage drops may occur 
and this can influence other equipment (e.g. 
dimming lights). So for technical reasons we 
advise, if the mains-impedance is Zmax<0.318 
Ohm, these disturbances are not expected. 
If you require further clarification, you may 
contact your local power supply authority. 

Caution: 

This packaging contains sharp 

objects. Take care when unpacking. This 
machine could require two persons to lift, 
assemble and move this machine. Remove 
the machine, together with the accessories 
supplied from the packaging. 
Check carefully to ensure that the machine 
is in good condition and account for all the 
accessories listed in this manual. Also make 
sure that all the accessories are complete. 
If any parts are found to be missing, the machine 
and its accessories should be returned together 
in their original packaging to the retailer. 
Do not throw the packaging away; keep it safe 
throughout the warranty period. Dispose of  

the packaging in an environmentally  
responsible manner. Recycle if possible. Do not 
let children play with empty plastic bags due to 
the risk of suffocation.

SERIAL NO. / BATCH CODE 

The serial number can be found on the motor 
housing of the machine.

  

For instructions on how to identify the batch 
code, please contact the Evolution Power 
Tools helpline or go to: 
www.evolutionpowertools.com 
 
 
 
 
 
 
 
 
 
 

10

11

www.evolutionpowertools.com

www.evolutionpowertools.com

DE

EN

ES

FR

IT

PL

PT

RO

Содержание 052-0001




























































































Отзывы:

Нет отзывов