Evolution 026-0007 Скачать руководство пользователя страница 15

15

www.evolutionpowertools.com

EN

DE

Fig. 14

Fig. 13

If a very precise bevel angle is required, then the blade setting 
should be checked using a vernier angle gauge (not supplied) 
and adjusted accordingly.
•   Loosen the Bevel Locking Mechanism found at the front of the 

machine, by pulling the lever upwards. (Fig. 13)

•  Tilt the blade to the required angle as indicated on the 

quadrant protractor scale. (Fig. 14)

•  Tighten the Bevel Locking Mechanism securely when  

the desired bevel angle has been achieved by pushing the 
lever downwards.

(14) 

OPERATING ADVICE

(PRE OPERATION CHECKS)

Note: As all operating environments will be unique and diverse, 
Evolution Power Tools offers the following general advice on safe 
operational procedures and practices for the consideration of the 
operator.

This advice cannot be exhaustive as Evolution has no influence 
on the type of workshops or working environments in which 
these machines may be used.

We recommend that the operator seeks advice from a competent 
authority or the workshop supervisor if they are at unsure of any 
aspect of using these machines.

It is important that routine safety checks are carried out (at each 
time of usage) before the operator uses the machine. 

WARNING: These pre-use safety checks should be carried out 
with the machine disconnected from the mains power supply.
•  Check that all safety guards are operating correctly, and that 

all adjustment handles/screws are securely tightened.

•  Check that the blade is secure and installed correctly. Also 

check that it is the correct blade for the material being cut.

•   Check the integrity of the power cord.
•   Whenever possible clamp the workpiece to a rigid support 

structure such as a workbench, saw horse or similar.

•   he operator should always be aware of the position and 

routing of the power cable.

(15) 

PPE

• 

The operator should wear all relevant PPE (Personal Protection 
Equipment) necessary for the task ahead. This could include 
safety glasses,,full face mask, dust masks, safety shoes etc.

Содержание 026-0007





















Отзывы: