manualshive.com logo in svg

Evinrude E-Tec 40 HP, Руководство по обслуживанию, Страница: 108 / 426

Поделиться
Скачать
Evinrude E-Tec 40 HP Скачать руководство пользователя страница 108

106

ELECTRICAL AND IGNITION

TILT/TRIM RELAY TEST

TILT/TRIM RELAY TEST

The  tilt and   trim (TNT) modu le con tains the   cir-

cuitry and relays  required for power trim and tilt

operation.

The tilt an d trim  switch  provides B+ inp ut to

green/white or blue/white wire of the TNT module.

Operation

The relay activates when B+ input from the switch

is supplied to terminal 86 of the internal relays. 

Terminal 87a connects to ground (B–).

Terminal 87 connects to B+.

Terminal 30 connects TNT motor.

Terminals 87a and 30 are connected when relay is

not activated. This supp lies ground (B–) connec-

tion to TNT motor.

Terminals 87 and 30 are no rmally ope n. B+   is

applied to terminal 30   when  relay  is act ivated.

This supplies ground B+ connection to TNT motor.

Refer to 

Tilt and Trim Module Diagram

.

Test Procedure

Make sure r ed and black wire s are connected to

12 V battery power supply. 

Set voltmeter to 12 VDC scale. Connect test leads

to terminals “A” and “B” of TNT motor connector. 

Use a wire jumper to alternately connect B+ to ter-

minals “1” and “2” of tilt and trim switch connector.

The met er mu st indicate  battery volt age ( 12 V)

with B+ connected to either terminal.

EXHAUST WATER VALVE 
TEST

Disconnect electrical connector  from wate r valve

solenoid. Use an ohmmeter to measure solenoid

resistance.

1.

Tilt and trim module

006754

1

Tilt and Trim Module Diagram

1.

Green/white wire

2.

Blue/white wire

3.

B+, red wire

4.

B–, black wire

5.

TNT motor connector

6.

TNT switch connector

002063

1.

Water valve electrical connector

004297

Water Valve Solenoid Resistance

295 

Ω 

± 20 @ 77°F (25°C)

3

4

1

2

6

5

1

Содержание E-Tec 40 HP











































































































































































































































































































































































































































Отзывы:

Нет отзывов