background image

7

IMPORTANT SAFETY MESSAGES

This Operator’s Guide contains essential in-

formation to help prevent personal injury and

damage to equipment. Safety messages ap-

pear throughout this Guide in the applicable

section. 
Be careful! Human error is caused by many

factors: carelessness, fatigue, overload, pre-

occupation, unfamiliarity of operator with the

product, drugs and alcohol to name a few.

Damage to your boat and outboard can be

fixed in a short period of time, but injury or

death, has a lasting effect.

SAFETY MEASURES — General

A

 WARNING

For your safety and the safety of others,

follow all safety warnings and recom-

mendations. Do not disregard any of the

safety precautions and instructions. 
Anyone operating your boat should first

read and understand this guide before

they operate your boat and outboard.

To fully appreciate the pleasures, enjoy-

ment and excitement of boating there are

some basic rules that should be ob-

served and followed by any boater.

Some rules may be new to you and oth-

ers may be common sense or obvious...

irrespective, take them seriously!

Be sure at least one of your passengers

knows how to handle your boat in case of

an emergency.

All passengers should know the location

of emergency equipment and how to use

it.

Know the marine traffic laws and obey

them.

All safety equipment and personal floata-

tion devices must be in good condition

and suitable for your type of boat. Always

comply with the regulations that apply to

your boat.

Remember, gasoline fumes are flamma-

ble and explosive. Always adhere to the

fueling procedure contained in this Oper-

ator’s Guide and those given to you by

the fueling station. Always verify fuel lev-

el before use and during the ride. Apply

the principle of 1/3 fuel to destination, 1/

3 back and 1/3 reserve fuel supply. Do

not carry spare fuel or flammable liquids

in any storage or engine compartments.

Whenever running the engine, assure

there is proper ventilation to avoid the ac-

cumulation of carbon monoxide (CO),

which is odorless, colorless, and taste-

less, and can lead to unconsciousness,

brain damage, or death if inhaled in suffi-

cient concentrations. CO accumulation

can occur while docked, anchored, or un-

derway, and in many confined areas

such as the boat cabin, cockpit, swim

platform, and heads. It can be worsened

or caused by weather, mooring and oper-

ating conditions, and other boats. Avoid

exhaust fumes from your engine or other

boats, provide proper ventilation, shut off

your engine when not needed, and be

aware of the risk of backdrafting and con-

ditions that create CO accumulation. In

high concentrations, CO can be fatal

within minutes. Lower concentrations are

just as lethal over long periods of time.

Avoid standing up or shifting weight sud-

denly in light weight boats.

Keep your passengers seated in seats.

The boat’s bow, gunwale, transom and

seat backs are not intended for use as

seats.

Insist on the use of personal floatation

devices, approved by the U.S. Coast

Guard, by all passengers when boating

conditions are hazardous, and by chil-

dren and nonswimmers at all times.

Proceed with caution and at very low

speed in shallow water. Grounding or

abrupt stops may result in personal injury

or property damage. Also be alert for de-

bris and objects in the water.

Содержание E-TEC 115



























































































Отзывы: