Evinrude E-TEC 115 Скачать руководство пользователя страница 63

Страница: 63 / 90



NSTALLATION

PROPELLER

Propeller Selection

To select the correct propeller for your boating

application, your boat and outboard MUST be

water tested. See your Dealer for assistance.

IMPORTANT:

The correct propeller for your

boat, under normal load conditions, will allow

the engine to run near the midpoint of the

RPM operating range at full throttle. Refer to

Specifications

on page 69.

Standard vs. Counter Rotation

Right-hand propellers are considered stan-

dard rotation propellers. When propelling a

boat forward, the propeller rotates in a right-

hand (clockwise) direction as viewed from the

rear.
Left-hand propellers are considered counter

rotation propellers. When propelling a boat

forward, the propeller rotates in a left-hand

(counterclockwise) direction as viewed from

the rear.

Installation

Apply

Triple-Guard

grease to

the entire propeller shaft before installing

the propeller. At least annually, remove

the propeller and check for debris. Clean

the shaft and regrease it before reinstall-

ing a propeller.

Slide thrust washer onto shaft with shoulder

facing aft.
Slide propeller onto shaft, engaging the

splines and seating it on the thrust bushing.
Slide spacer onto the shaft and engage the

propeller shaft splines.

Wedge a block of wood between the propeller

blade and the anti-ventilation plate.

WARNING

When servicing the propeller, always

shift the outboard to NEUTRAL position,

turn the key switch OFF, and twist and

remove all spark plug wires so the out-

board cannot be started accidentally.

1. Right-Hand (clockwise)
2. Left-Hand (counterclockwise)

000033

WARNING

In dual-outboard installations, check to

make sure correct propellers are

installed on each outboard before

aggressively operating your boat. Shift

each engine individually into FORWARD

or REVERSE, at idle speed only. If the

boat moves opposite the direction indi-

cated by the remote control handle, the

wrong propeller has been installed on

the outboard being checked.

CO2917

NOTICE

Содержание E-TEC 115



























































































Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды

Evinrude E-TEC 115, Оригинальное руководство пользователя

Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды