Evinrude E-TEC 115 Скачать руководство пользователя страница 51

Страница: 51 / 90



ERVICE

3) Remove propeller and place the shift lever

in NEUTRAL position.

4) Connect garden hose to flushing device

and install flushing device on gearcase.

5) Turn on the water. Keep the water pres-

sure between 20 and 40 psi (140 to

300kPa).

6) Start the engine and RUN AT IDLE

SPEED. Flush engine for at least five min-

utes. A steady stream of water must flow

from exhaust relief port of outboard.

7) Turn engine OFF. Leave the outboard in

vertical position long enough to completely

drain the powerhead.

FUSE

A blown fuse will not allow the engine to start.

Replace it with a fuse of the same rating. A

spare fuse is provided.
Repeated fuse failures indicate a potentially

serious problem. Do not replace it with higher

rated fuse; see your Dealer for service.

Fuse Replacement

Use only fuses of the same

rating. Your

Evinrude E-TEC

outboard

uses 10-amp fuses.

Remove engine cover. Install spare fuse in

place of failed fuse.
Detach fuse from plug by pulling down on fuse

connector clip. Install spare fuse in place of

failed fuse.

Failure to install cover

securely may cause electrical problems.

1. Auxiliary water inlet holes

008358

1. Flushing device
2. Stream of water

008527

60° V4 & V6 Models

1. Fuse (port)
2. Spare fuse

004999

90° V6 Models

1. Fuse (starboard)
2. Spare fuse

003984

NOTICE

Содержание E-TEC 115



























































































Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды

Evinrude E-TEC 115, Оригинальное руководство пользователя

Результаты поиска

Содержание E-TEC 115

Отзывы:

Похожие инструкции для E-TEC 115

Бренды по названию

Популярные бренды