PCoIP
Remote
PC
TX/RX
LINK
DVI-1
DVI-2
EVGA PCoIP
®
Visual Guide
Package Contents
PD01 Desktop Portal Package Includes:
▪
Portal device with stand
▪
Power adaptor
▪
Power cord
▪
Ethernet cable (2m)
▪
User manual CD
▪
Quick Visual Guide
HC01 PCIe Host Card Package includes:
▪
Host card with full hight and
low profile bracket
▪
DMS-59 to dual DVI cable (45cm)
▪
Power Button cable
▪
Ethernet cable (2m)
▪
User manual CD
▪
Quick Visual Guide
1
PCoIP
®
Desktop Portal Installation
1. Be sure the monitor and the Portal are turned off and disconnected from AC power.
2. Use a DVI cable to connect the monitor to the Portal’s DVI Port 1
(9)
.
3. Plug the monitor’s power cable into an AC outlet and power it on.
4. If you are using dual monitors, repeat Steps 1 through 3 but connect the second monitor to the
Portal’s DVI Port 2
(10)
.
5. Connect a USB keyboard and mouse to the Portal’s rear USB ports
(7)
.
6. Use an Ethernet cable to connect the Ethernet switch or router to the Portal’s Ethernet jack
(8)
.
7. Connect the Portal power supply to the Portal’s power jack
(12)
, then plug the Portal power supply
into a surge-protected AC outlet.
8. Optionally connect the following devices to the Portal:
▪
PC speaker to Speaker jack
(11)
▪
Headphones and MIC to Headphone
(5)
and Microphone jacks
(6)
▪
USB peripherals to auxiliary USB ports
(4)
9. Power on the Portal by pushing the power button
(2)
. The power button will light steady green and
the monitor will display the On Screen Display (OSD).
Font
Back
WARNING
1. Always power down and disconnect devices from AC power before handling them.
Failure to do this can result in personal injury or equipment damage. Some circuitry
on the host PC can continue to operate even though the front panel power switch is off.
2. The Standalone Mode Power Connector on the host card must be disconnected when
the host card is operating in PCIe powered mode. Failure to do this can result in damage
to the host card.
NOTE
If the monitor does not show the On Screen Display (OSD), check all connectors and be sure the
monitor and Portal are powered on. Note the LED indicators:
▪
Off: AC power is off
▪
Solid yellow: AC power is on and Portal power is off
▪
Solid green: Portal power is on
▪
Blinking green: Host PC is in low-power state.
(7) Rear USB Ports
PColP
®
LED (1)
Portal Power Button (2)
Remote PC Power Button (3)
Front USB Ports (4)
Headphone Jack (5)
Microphone Jack (6)
(8) Ethernet Port
(9) DVI Port 1
(10) DVI Port 2
(11) Speaker Jack
(12) 12VDC Power Jack
DVI-1 Connector (13)
Standalone Mode Power Connector (15)
Power Button Cable Connector (16)
Standalone Mode Jumper (17)
Ethernet Port (21)
DMS-59 Port (22)
(18) Disable WOL Jumper
(19) Heartbeat LED
(20) Factory Default Reset
(24) Wake Configuration Jumper
(23) PCIe Connector
DVI-2 Connector (14)
1
2
PD01 PCoIP
®
Desktop Portal
HC01 PCoIP
®
PCI-E Host Card
2
PCoIP
®
PCIe Host Card Installation
1. Check the jumpers on the Host card to ensure they are in the correct setting. See Host Card Jumper
Settings for details.
2. Be sure the Host PC is turned off and unplugged from AC power.
3. Open the PC’s case.
