evertz exponent 500IDA9-IG Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

evertz exponent 500IDA9-IG Series Скачать руководство пользователя страница 12

Frame Manual

500IDA9-IG Series SDI IntelliGent Distribution Amplifier

6.

VISTALINK

®

MODULE CONTROL

This section describes the VistaLINK

®

control and monitoring available on the 500IDA9-IG.

6.1.

WHAT IS

VISTA

LINK

®

?

VistaLINK

®

is Evertz’s remote monitoring and configuration platform which operates over an Ethernet

network using Simple Network Management Protocol (SNMP). SNMP is a standard computer network
protocol that enables different devices sharing the same network to communicate with each other.
VistaLINK

®

provides centralized alarm management, which monitors, reports, and logs all incoming alarm

events and dispatches alerts to all the VLPro Clients connected to the server. Card configuration through
VistaLINK

®

PRO can be performed on an individual or multi-card basis using simple copy and paste

routines, which reduces the time to configure each module separately. Finally, VistaLINK

®

enables the

user to configure devices in the network from a central station and receive feedback that the configuration
has been carried out.

There are 3 components of SNMP:

1. An SNMP manager also known as a Network Management System (NMS) is a computer running

special software that communicates with the devices in the network. Evertz

Vista

LINK

®

Pro Manager

graphical user interface (GUI), third party or custom manager software may be used to monitor and
control Evertz

Vista

LINK

®

enabled products.

2. Managed devices, each with a unique address (OID), communicate with the NMS through an SNMP

Agent. Evertz VistaLINK

®

enabled 500series modules reside in the 3RU 500FR MultiFrame and

communicate with the manager via the 500FC VistaLINK

®

frame controller module, which serves as

the Agent.

3. A virtual database known as the Management Information Base (MIB) lists all the variables being

monitored, which both the Manager and Agent understand. Please contact Evertz for further
information about obtaining a copy of the MIB for interfacing to a third party Manager/NMS.

For more information on connecting and configuring the

Vista

LINK

®

network, see the 500FC Frame

Controller chapter.

Page - 8

Revision 1.1.1

«
...
10
11
12
13
14
...
»

Содержание exponent 500IDA9-IG Series





















Отзывы:

Нет отзывов