evertz 7847FSEDA Series Скачать руководство пользователя страница 48

Страница: 48 / 86

7847FSEDA Series

Frame Synchronizer and Distribution Amplifier

Page - 38

Revision 0.1

Figure 5-16: Video Path Configuration - Embedded Audio Mixer Tab

Source – X & Y:

These controls allow the user to route one of the selectable mixer input audio

sources to the Corresponding input (X or Y) of the embedded audio output channel mixer.

Gain – X & Y:

These controls allow the user to set the value of the gain for the mixer input channel (X

or Y). The user can adjust the gain of the selected mixer channel (X or Y) by adjusting the
corresponding slider control. The supported range for gain adjustments is

-24dB to +24dB

. The gain

can be adjusted with

0.1dB

precision.

Inversion – X & Y:

These controls allow the user to invert the phase (180 degree phase shift) of the

corresponding mixer input channel. By selecting

Normal,

the module will pass the mixer input audio

through with no processing. By selecting

Invert,

the module will invert the phase of the mixer input

audio channel (X or Y).

Содержание 7847FSEDA Series























































































Результаты поиска

Содержание 7847FSEDA Series

Отзывы:

Бренды по названию

Популярные бренды

evertz 7847FSEDA Series, Руководство пользователя

Результаты поиска

Содержание 7847FSEDA Series

Отзывы:

Бренды по названию

Популярные бренды