evertz 7707VB-8-ASI-OC3 Скачать руководство пользователя страница 23

Страница: 23 / 32

7700 MultiFrame Manual

7707VB-8-ASI-OC3 8 Channel ASI + Ethernet SONET / SDH Fiber Transceiver

Revision

1.0

Page - 19

4.2.2.1.

Setting the Optical Link Standard

The

Optical Link Standard

can be controlled using menu selections. To configure the

Optical Link

Standard

from the

CTRL

menu, use the toggle switch/pushbutton to select the

FIBR

menu item and then

choose the

STD

menu item.

CTRL

FIBR

STD

OC
SDH

The following selections are available:

SONET Interface

SDH

SDH Interface

4.2.2.2.

Setting the Behavior of Laser when no Signal is Applied

The behavior of the laser transmitter when there is no video signal applied to the coaxial video inputs can
be controlled using menu selections. To configure the

Laser Behavior

when

No Signal

is applied from the

CTRL

menu, use the toggle switch/pushbutton to select the

FIBR

menu item and then choose the

LASR

menu item.

CTRL

FIBR

LASR

CONT
DISC

The following selections are available:

CONT

Laser is on regardless of input

DISC

Laser is on with signal present and off with no signal present

4.2.2.3.

Setting the Clock Source

Three clock settings are available for serial fiber output. To configure the

Clock Source

from the

CTRL

menu, use the toggle switch/pushbutton to select

FIBR

menu item and then choose the

REF

menu item.

CTRL

FIBR

REF

XO
LINK
AUTO

The following selections are available:

Sets the Stratum 3 oscillator as the clock source

LINK

Sets the POS Link clock as the clock source

AUTO

Automatically select the best setting

4.2.2.4.

Clearing the Counters

The counter/timer clear can be controlled using menu selections. To configure the counter/timer clear from
the

CTRL

menu, use the toggle switch/pushbutton to select the

FIBR

menu item and then choose the

CIC

menu item.

Содержание 7707VB-8-ASI-OC3

































Результаты поиска

Содержание 7707VB-8-ASI-OC3

Отзывы:

Похожие инструкции для 7707VB-8-ASI-OC3

Бренды по названию

Популярные бренды

evertz 7707VB-8-ASI-OC3, Руководство пользователя

Результаты поиска

Содержание 7707VB-8-ASI-OC3

Отзывы:

Похожие инструкции для 7707VB-8-ASI-OC3

Бренды по названию

Популярные бренды