evertz 570NAT-HW-X19 Скачать руководство пользователя страница 39

Страница: 39 / 56

570NAT-HW-X19

High Density Network Address Translator

Revision 1.0

Page - 29

Input Source IP Address:

This control is used in NAT mode to configure the output header with the

desired source IP address.

Input Bitrate:

This monitor will display the bit rate of the streams that are being received in kbps.

Input Bitrate Cap:

This control allows the user to set a cap on the bitrate for each flow in Kbps.

4.5.4. WAN to LAN: Address Translation Configuration

Flows 1 to 256

Output Mode:

This control is used to set the output mode on the flow stream. Options are

Pass

Through

Modify.

Pass Through

will enable the stream to pass through without making any changes

to the headers while

Modify

enables changes to the headers.

Source IP Address:

This control is used in NAT mode to configure the output header with the desired

source IP address.

Source UDP Port:

This control is used in NAT mode to configure the output header with the desired

source UDP Port.

Destination IP Address:

This control is used in NAT mode to configure the output header with the

desired destination IP address.

LAN Interface:

This control allows the user to set the LAN interface this flow passed through in WAN

to LAN, the options given are to flow directly through data port or through a NAT virtual interface

(Interfaces 1-15, Figure 4-11 shows an abbreviated menu).

Destination MAC for Unicast IP:

This control is used to enter the Destination MAC address.

Destination UDP Port:

This control is used in NAT mode to configure the output header with the

desired destination UDP Port.

Содержание 570NAT-HW-X19

























































Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды

evertz 570NAT-HW-X19, Руководство пользователя

Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды