evertz 570NAT-HW-X19 Скачать руководство пользователя страница 24

Страница: 24 / 56

570NAT-HW-X19

High Density Network Address Translator

Page - 14

Revision

1.0

Mode of Operation:

Within this drop down menu the user can configure the desired mode of operation

for each core of the 570NAT-HW-X19.
The NAT can be set to:

IP NAT

MC-In-MC NAT + IP NAT

Port Based NAT

VLAN Based NAT.

Once a core has been set to a mode of operation, the settings for the mode of operation on that core

can be set by selecting that core on the WebEASY

main menu sidebar (shown in Figure 4-2).

Each mode of operation can be found in the following sections: Port Based NAT [Section 4.3], VLAN

Based NAT [Section 4.4], IP NAT [Section 4.5], MC-in-MC NAT + IP NAT [Section 4.6].

4.1.3. Data Port Traffic Monitoring

For each of the 12 Data ports (6 pairs) the following parameters can be monitored. Port are selected as

WAN-LAN pairs.

Link Speed:

This monitor will automatically detect the link speed of the SFP module installed.

Link Status:

This field displays the physical link status of the associated data port as either

Down

Received Bandwidth (kbps):

This field displays the bit rate received by the associated data port in

kbps.

Transmit Bandwidth (kbps):

This field returns the bit rate transmitted by the associated data port in

kbps.

Received Healthy Frames:

This parameter displays number of good Ethernet packets received.

Transmitted Healthy Frames

: This parameter displays number of good Ethernet packets transmitted.

Received Corrupted Frames:

This parameter displays number of Ethernet packets received with

errors

Transmitted Corrupted Frames:

This parameter displays number of Ethernet packets transmitted

with errors.

Clear All Statistics

: This control button allows the user to clear all the statistics.

Содержание 570NAT-HW-X19

























































Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды

evertz 570NAT-HW-X19, Руководство пользователя

Результаты поиска

Содержание 570NAT-HW-X19

Отзывы:

Похожие инструкции для 570NAT-HW-X19

Бренды по названию

Популярные бренды