evertz 2430RX-J2K-IP Series Скачать руководство пользователя страница 37

Страница: 37 / 44

2430RX-J2K-IP

JPEG2000 to HDMI Converter User Manual

Revision 0.1

Page - 29

6.7.

ERROR MONITOR

Figure 6-8: Error Monitor Tab

Video Error Monitor

Video CC Errors:

This field displays the number of Continuity Counter error incidents for Video PID.

Range for this value can be from 0 to 65535.

Video CRC Errors:

This field displays the number of CRC error incidents for Video. Range for this

value can be from 0 to 65535.

Audio CC Error Monitor:

This field displays the number of Continuity Counter error incidents for Audio

PIDs 1 through 4.

Ancillary Error Monitor:

This field displays the number of Continuity Counter error incidents for

Ancillary PIDs

PCR Error Monitor:

This field displays the number of Discontinuity Error incidents for PCR PIDs.

Reset Counters:

This control will reset all the error counters.

Содержание 2430RX-J2K-IP Series













































Результаты поиска

Содержание 2430RX-J2K-IP Series

Отзывы:

Похожие инструкции для 2430RX-J2K-IP Series

Бренды по названию

Популярные бренды

evertz 2430RX-J2K-IP Series, Руководство пользователя

Результаты поиска

Содержание 2430RX-J2K-IP Series

Отзывы:

Похожие инструкции для 2430RX-J2K-IP Series

Бренды по названию

Популярные бренды