evertz 2430RX-J2K-IP Series Скачать руководство пользователя страница 35

Страница: 35 / 44

2430RX-J2K-IP

JPEG2000 to HDMI Converter User Manual

Revision 0.1

Page - 27

6.6.

PROGRAM MONITOR

Figure 6-7: Program Monitor Tab

Program Num In TS:

This parameter returns the actual program number that is being decoded. Range

for this value can be from 0 to 65535. When in

Manual PID Selection Mode

no value will be displayed.

PM TPID:

This parameter returns the PID for the PMT, for the program being decoded. Range for this

value can be from 0 to 8191. When in

Manual PID Selection Mode

no value will be displayed.

PCR PID:

This parameter returns the PID which has the PCR information for the program being

decoded. Range for this value can be from 0 to 8191. When in

Manual PID Selection Mode

no value

will be displayed.

Num Video Streams:

This parameter returns the number of Video Streams in the program which are

being decoded. Range for this value can be from 0 to 100. When in

Manual PID Selection Mode

value will be displayed. Also, it is assumed there is only one video stream in one program.

Num Audio Streams:

This parameter returns the number of Audio Streams in the program which are

being decoded. Range for this value can be from 0 to 100. When in

Manual PID Selection Mode

value will be displayed.

Содержание 2430RX-J2K-IP Series













































Результаты поиска

Содержание 2430RX-J2K-IP Series

Отзывы:

Похожие инструкции для 2430RX-J2K-IP Series

Бренды по названию

Популярные бренды

evertz 2430RX-J2K-IP Series, Руководство пользователя

Результаты поиска

Содержание 2430RX-J2K-IP Series

Отзывы:

Похожие инструкции для 2430RX-J2K-IP Series

Бренды по названию

Популярные бренды