Everlz 7707DT Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 38

Everlz 7707DT Скачать руководство пользователя страница 27

7700 MultiFrame Manual

7707DT RS-232/422/485 Fiber Data Transceiver

Revision

1.8

Page - 21

5. JUMPER

CONTROLS

Several jumpers, located at the front of the module are used to preset various operating modes. Figure
4-1 shows the locations of the jumpers.

5.1.

SELECTING THE CARD ID

Configuration of the

CARD ID

jumper is required for single-fiber 7707DT and 7707DT-GPIO versions only.

To maintain a robust optical link between two companion 7707DT cards, the

CARD ID

jumper must be set

differently on each.

CARD ID:

To maintain a link between two 7707DT cards, set this jumper to position A on one, and to

position B on the other. Position B may be selected on either of the cards, as long as position
A is selected for the companion card.

5.2.

SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED
BY THE GLOBAL FRAME STATUS

The FRAME STATUS jumper determines whether local faults (as shown by the Local Fault indicator) will
be connected to the 7700FR frame's global status bus.

FRAME STATUS:

To monitor faults on this module with the frame status indicators (on the Power

Supply FRAME STATUS LED's and on the Frame's Fault Tally output) install this jumper in the
On position (default)

When this jumper is installed in the Off position local faults on this module will not be
monitored.

5.3.

CONTROL JUMPER (No Longer Used)

The control jumper is no longer considered by recent code versions, and if installed, should be
disregarded by the user.

5.4.

CONFIGURING THE MODULE FOR FIRMWARE UPGRADES

RUN/UPGRADE:

The RUN/UPGRADE jumper is used when firmware upgrades are being done to the

module. For normal operation it should be installed in the

RUN

position. See the

Upgrading

Firmware

chapter in the front of the binder for more information.

To upgrade the firmware in the module unit pull it out of the frame. Move the RUN/UPGRADE
jumper J16 into the

UPGRADE

position. Install the Upgrade cable provided (located in the

vinyl pouch in the front of the binder) onto SERIAL header J27 at the card edge. Re-install the
module into the frame. Run the upgrade as described in

Upgrading Firmware

chapter in the

front of the binder. Once the upgrade is complete, remove the module from the frame, move
J16 into the

RUN

position, remove the upgrade cable and re-install the module. The module is

now ready for normal operation.

«
...
25
26
27
28
29
...
»

Содержание 7707DT







































Отзывы:

Нет отзывов