Eurotherm Parker SDS Drives 6054-HTTL-00 Скачать руководство пользователя страница 1

Unit 6, St Martin’s Park

Moorend Farm Avenue

Cabot Park, Avonmouth

Bristol, BS11 0RS

Tel: +44 (0)1179 381800

Fax: +44 (0)1179 381801

Email: [email protected]

Web: www.sdsdrives.com

formerly

now

then

WARNING!

Disconnect all sources of power before attempting installation. Injury or death

could result from unintended actuation of controlled equipment.

Caution

This option contains ESD (Electrostatic Discharge) sensitive parts. Observe static control

precautions when handling, installing and servicing this option.

Used on : 

605C, 690+ Frames C-K

1. 

Unpack and handle the Option using correct static safety procedures.

2. 

Remove the inverter terminal cover and securing screws.

3. 

  Carefully plug the Option into the left-hand port (as illustrated above) ensuring correct alignment of the connector and 

tighten the earthing screw. You can operate the Inverter with the Speed Feedback and/or a Communications Technology 

Box, but you cannot use two options of the same kind.

2

 

HTTL Speed Feedback Technology Box 

Installation 

WARNING!

 

Disconnect all sources of power before attempting installation. Injury or death 

could result from unintended actuation of controlled equipment. 

Caution 

This option contains ESD (Electrostatic Discharge) sensitive parts. Observe static control 

precautions when handling, installing and servicing this option. 

Wiring the System : 605C, 690+ Frames C-K 

earthing screw

Figure 1  Installing the HTTL Speed Feedback Technology Box Option 

(605C illustrated) 

1. Unpack and handle the Option using correct static safety procedures. 
2. Remove the inverter terminal cover and securing screws. 
3. Carefully plug the Option into the left-hand port (as illustrated above) ensuring correct 

alignment of the connector and tighten the earthing screw. You can operate the Inverter with 

the Speed Feedback and/or a Communications Technology Box, but you 

cannot

 use two 

options of the same kind. 

This manual was downloaded at: www.sdsdrives.com 

+44 (0)117 938 1800

Figure 1 Installing the HTTL Speed Feedback 

Technology Box Option (605C illustrated)

PART NUMBER: 

6054-HTTL-00

Содержание Parker SDS Drives 6054-HTTL-00

Страница 1: ... use two options of the same kind HTTL Speed Feedback Technology Box ation WARNING Disconnect all sources of power before attempting installation Injury or death could result from unintended actuation of controlled equipment Caution This option contains ESD Electrostatic Discharge sensitive parts Observe static control precautions when handling installing and servicing this option Wiring the Syste...

Страница 2: ...to give a threshold of 3V when using a differential encoder and to 8V when using a single ended encoder Factory default is with switches 1 2 set in the ON position 3V Terminal Block TB1 Connections For correct operation A A B and B must be connected as shown If any is left unconnected the HTTL speed feedback technology box will not operate Note The M and H inputs are not normally connected these a...

Страница 3: ...panel mounting option for dirty air cooling are available from SSD Drives Mounting the Inverter The unit must be mounted vertically on a solid flat vertical surface It can be wall mounted or mounted inside a suitable cubicle depending upon the required level of EMC compliance refer to Chapter 11 Technical Specifications and Chapter 12 Certification for the Inverter Minimum Air Clearances Ventilati...

Страница 4: ... 0 9 92 150 0 5 90 150 0 5 90 245 0 9 65 Slot 7mm wide Use M5 or M6 fixings Frame E 32 5 72 668 6 26 30 630 0 24 80 676 0 26 60 257 0 10 10 150 0 5 90 150 0 5 90 312 12 30 Use M6 fixings Frame F 41 90 4 720 0 28 30 700 0 27 60 Not applicable 257 0 10 10 150 0 5 90 150 0 5 90 355 0 14 00 Use M6 fixings 197 0 8 04 when unit fitted with System Board All dimensions are in millimetres inches Note For d...

Отзывы: