Eurotech ZEUS Скачать руководство пользователя страница 43

Страница: 43 / 136

ZEUS Technical Manual

Detailed hardware description

Unsupported PC/104 interface features

The ZEUS does not support the following PC/104 bus features:

•

PC/104 IRQ9, IRQ14 and IRQ15 are not available.

•

DMA is not supported. Therefore, AEN signal is set to a constant logical zero.

•

Bus mastering is not supported. Therefore, do not connect any other master add-

on board to the ZEUS PC/104 interface.

•

Shared interrupts are not supported. Do not connect more than one add-on board

to the same interrupt signal line.

•

BALE signal is set to a constant logical one as the address is valid over the entire

bus cycle. Add-on PC/104 boards that implement transparent latch on address

lines LA17-LA23 are compatible with the ZEUS implementation of BALE.

•

The PXA270 PCMCIA memory controller does not support 8-bit memory read

accesses for common memory space.

•

The PXA270 PCMCIA memory controller does not support PC/104 MEMCS#

signalling, so there is no support for dynamic bus sizing.

Содержание ZEUS









































































































































Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды

Eurotech ZEUS, Техническое руководство

Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды