Eurotech ZEUS Скачать руководство пользователя страница 13

Страница: 13 / 136

ZEUS Technical Manual

Introduction

ZEUS support products

The following products support the ZEUS:

•

ZEUS Modem Board 1

, a low profile module attached to the solder side of the

ZEUS main board. It provides the following wireless connectivity options:

- Quad band GSM/GPRS: Sony Ericsson GR64 or Dual band Siemens MC39i

module.

- iDEN: Motorola iO270 module (includes internal GPS receiver).
- GPS: Fastrax iTRAX0312 channel GPS receiver module.
See

ZEUS Modem Board 1

, page

118

, for further details.

•

ZEUS Modem Board 2

, a low profile module attached to the solder side of the

ZEUS board. It provides the following wireless connectivity:
- Quad band GSM/GPRS: TELIT GE863-GPS module (includes internal GPS

receiver).

, for further details.

•

ZEUS Modem Board 3

, a low profile module attached to the solder side of the

ZEUS main board. It provides the following wireless connectivity:
- GSM/GPRS: SierraWireless MC8780/MC8775/MC8755 modules.
- CDMA: SierraWireless MC5720/MC5725 modules.
- GPS: Fastrax iTRAX0312 channel GPS receiver module.
See

ZEUS Modem Board 3

, p age

119

, for further details.

•

ZigBee module (ZMx)

, a direct plug-in option for the ZEUS board that provides

ZigBee (see

www.zigbee.org

) and IEEE 802.15.4 compatible wireless connectivity.

It provides a fully functioning IEEE802.15.4 / ZigBee controller.
See

IEEE802.15.4 / ZigBee module (ZMx)

, page

, for further details.

•

ZEUS-FPIF

(Flat Panel Interface), a simple board that enables easy connection

between the ZEUS and a variety of LCD flat panel displays.
See

ZEUS-FPIF

, page

122

, for further details.

•

ZEUS-FPIF-CRT

, a board that allows the ZEUS to drive a CRT Monitor or an

analogue LCD flat panel. Sync on green and composite sync monitors are not

supported.
See

ZEUS-FPIF-CRT

, page

127

, for further details.

Contact

Eurotech Sales

, page

, for further information about any of the above

products.

Содержание ZEUS









































































































































Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды

Eurotech ZEUS, Техническое руководство

Результаты поиска

Содержание ZEUS

Отзывы:

Бренды по названию

Популярные бренды