Eurotech CPU-1450 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 43

Eurotech CPU-1450 Скачать руководство пользователя страница 13

13

CPU-1450 SPM block diagram architecture

Event Input Signals and Their Usage

Transitions rules for ICH2:

Present State

Transition Trigger

Next State

G0/S0/C0

Processor halt instruction
Level 2 Read
Level 3 Read
SLP_EN bit set
Power Button Override
Mechanical Off / Power Failure

G0/S0/C1
G0/S0/C2
G0/S0/C3
G1/Sx or G2/S5state
G2/S5
G3

G0/S0/C1

Any Enabled Break Event
STPCLK# goes active
Power Button Override
Power Failure

G0/S0/C0
G0/S0/C2
G2/S5
G3

G0/S0/C2

Any Enabled Break Event
STPCLK# goes inactive and previously in C1
Power Button Override
Power Failure

G0/S0/C0
G0/S0/C1
G2/S5
G3

G0/S0/C3

(ICH2-M only)

Any Enabled Break Event
STPCLK# goes inactive and previously in C1
Power Button Override
Power Failure

G0/S0/C0
G0/S0/C1
G2/S5
G3

G1/S1,

G1/S3, or

G1/S4

Any Enabled Wake Event
Power Button Override
Power Failure

G0/S0/C0 (For ICH2-M, see note 2)
G2/S5
G3

G2/S5

Any Enabled Wake Event
Power Failure

G0/S0/C0 (For ICH2-M, see note 2)
G3

G3

Power Returns

Optional to go to S0/C0 (reboot) or G2/S5 (stay off until power
button pressed or other wake event). (For ICH2 and ICH2-M,
see Note 1) (For ICH2-M, see note 2)

Table 4.

Transitions Rules for ICH2

An0065. CPU-1450 Soft Power Management

«
...
11
12
13
14
15
...
»

Содержание CPU-1450












































Отзывы:

Нет отзывов