Eurotech Apollo Скачать руководство пользователя страница 76

Страница: 76 / 145

APOLLO user manual

Issue G

Video (Intel IGD) control settings

You can specify settings that determine how the Internal Graphics Device operates.

To specify video (Intel IGD) control settings, highlight

Video (Intel IGD)

Control Sub-

Menu

in the

Advanced

menu and press

Enter

. The following screen is displayed:

The details you are prompted to specify are explained in the following table:

Field

Explanation

Default Primary Video
Adapter

Choose the type of video card to be used for the boot display
device. You can choose

PCI Video Adapter

Internal Video

If dual monitor support is required when using a PCI Video
Adapter, the Primary Video Adapter should be configured to
use the PCI Video Adapter.

MDA Seek

Choose

Enabled

if you want the system to seek an MDA

video adapter during boot.

IGD – Device 2

Choose whether to enable or disable the Internal Graphics
Device.

Содержание Apollo


















































































































































Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды

Eurotech Apollo, Руководство пользователя

Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды