Euromate 107447, Оригинальное руководство пользователя

Страница: 10 / 20

GB
10
• The distance towards the front between the front
grate and objects must be at least 65 cm.
Towards the back, the device must be clear for air
supply.
• With the pivoting model, the pivot area must be
kept clear.
• The device may not be fastened to the wall.
• The device may not be operated outdoors.
• The device may never be operated without
supervision.
• Never put objects through the ventilation grate
into the device. Mortal danger!
• Never subject the device to water or other liquids.
• The device may neither be operated in rooms
with a bathtub, shower or swimming pool nor
near washbasins or water connections.
• The device may not be covered. There is danger
of fire.
• Do not use adapters or extension cords.
• Do not use the heater in conjunction with a timer
or any other switch capable of automatic activa-
tion, as this creates a fire hazard.
• The heater must not be positioned beneath a wall
socket.
• This appliance can be used by children aged
from 8 years and above and by persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and if they
understand the hazards involved. Children shall
not play with the appliance. Cleaning and user
maintenance shall not be made by children with-
out supervision.
• Children of less than 3 years should be kept
away unless continuously supervised.
• Children aged from 3 years and less than 8 years
shall only switch on/off the appliance provided
that it has been placed or installed in its intended
normal operating position and they have been
given supervision or instruction concerning use
of the appliance in a safe way and understand
the hazards involved. Children aged from 3 years
and less than 8 years shall not plug in, regulate
and clean the appliance or perform user mainte-
nance.
• CAUTION! Some parts of this product can
become very hot and cause burns. Particular
attention has to be given where children and vul-
nerable people are present.
• Symbols appearing on your device may not be
removed or covered. Signs on the device that are
no longer legible must be replaced immediately.
Your device at a glance
►
Overview – p. 3
1. Air outlet
2. Control panel
3. Handle
4. Air inlet
5. Main switch
6. Power cord
Operation
Check before switching on!
Check the safe condition of the device.
– Check whether there are any visible defects.
– Check whether all parts of the device are firmly
attached.
– Check whether the switch is on [0] before you
insert the plug into the outlet.
Using the heater
►
Operation – p. 4
– Before inserting the plug into an electrical outlet,
make sure that the electrical supply in your area
matches that on the rating label of the heater.
– When plugged in the heater, turn on the main
power switch at the back of the heater.
– When in Standby mode, press the button [ ] to
start the heater, and the LED display will show
the room temperature.
– Low Power: About 800 W (Press the button [ ]
to have one [ ] lighten on)
– High Power: About 1500 W (Press the button [ ]
to have two [ ] lighten on together)
– Timer: Press the button [ ] repeatedly to set a
period after which the heater will turn itself off
(From 0 hour – 12 hours)
– Press the button [+] and [–] to adjust room tem-
perature. Temperature can be set from 10-35 °C.
Press
[+] to increase the temperature and [-] to
decrease the temperature. When the room tem-
perature is 4 °C lower than the set temperature of
the heater, it will work on high power. When the
room temperature is lower than the set tempera-
ture, it will work on low power. If the room temper-
ature reaches the set temperature, the heating
stops, but the fan is permanently on until the
room temperature is lower than the set tempera-
ture. Then, the heater automatically returns to
low power heating.
– Swing: Press the button [ ] to activate swing
function. Press it again to cancel the function.
– Press the button [ ] to turn off the heater, the
fan will keep operating for 30 seconds. This
design is to cool down the heater.
Warning:
– Before removing the plug from the socket, switch
off the heater and better wait for 30-60 second for
cooling down the heater to protect inner parts.
– Remote control should be powered by a button
cell – lithium battery CR2025
Read and observe the instructions for use
before using the product for the first time.
To prevent overheating, do not cover the
heater!
DANGER! Risk of injury! The device
must only be put into operation if no faults
are found during the check-up. If any part of
the device is defective, it must be replaced
before the next use.