www.eurolite.de
23
Laser
• This device includes a class 2M laser according to the
EN 60825-1:2007 regulation. Do not stare into the
beam! The accessible laser radiation is exclusively
within the visible spectral range (400 nm to 700 nm).
However, a short-term exposure (max. 0.25 seconds)
is not hazardous to the eye. A longer exposure is
prevented by the natural eyelid closing reflex.
Nevertheless, close your eyes or turn away
immediately if the laser beam hits the eye.
• The laser beams must not be viewed with optical
instruments such as magnifying lenses or telescopes.
• Never direct the laser beam to the eyes of persons or
animals.
• Caution when aligning the unit to a reflecting surface.
The laser beam may not hit the eye by reflection.
• Caution laser diode! Do not open or modify the unit.
A modification can result in a more hazardous laser
radiation which considerably deviates from the
specified values.
• Keep away children and amateurs! Never leave this
device running unattended.
• This laser product is not applicable for outdoor use.
Unpacking
• Please make sure that there are no obvious transport
damages. Should you notice any damages, do not
take the device into operation and immediately
consult your local dealer.
• Save the package and all packing materials. In the
event that a fixture must be returned to the factory, it
is important that the fixture be returned in the original
factory box and packing.
Protection Class
• This device falls under protection class I. The power
plug must only be plugged into a protection class I
outlet. The voltage and frequency must exactly be the
same as stated on the device. Wrong voltages or
power outlets can lead to the destruction of the device
and to mortal electrical shock.
Power Cord
• Always plug in the power plug least. The power plug
must always be inserted without force. Make sure that
the plug is tightly connected with the outlet.
• Never let the power cord come into contact with other
cables! Handle the power cord and all connections
with the mains with particular caution! Never touch
them with wet hands, as this could lead to mortal
electrical shock.
• Never modify, bend, strain mechanically, put pressure
on, pull or heat up the power cord. Never operate next
to sources of heat or cold. Disregard can lead to
power cord damages, fire or mortal electrical shock.
• The cable insert or the female part in the device must
never be strained. There must always be sufficient
cable to the device. Otherwise, the cable may be
damaged which may lead to mortal damage.
• Make sure that the power cord is never crimped or
damaged by sharp edges. Check the device and the
power cord from time to time.
• If extension cords are used, make sure that the core
diameter is sufficient for the required power
consumption of the device. All warnings concerning
the power cords are also valid for possible extension
cords.
• Always disconnect from the mains, when the device is
not in use or before cleaning it. Only handle the power
cord by the plug. Never pull out the plug by tugging
the power cord. Otherwise, the cable or plug can be
damaged leading to mortal electrical shock. If the
power plug or the power switch is not accessible, the
device must be disconnected via the mains.
• If the power plug or the device is dusty, the device
must be taken out of operation, disconnected and
then be cleaned with a dry cloth. Dust can reduce the
insulation which may lead to mortal electrical shock.
More severe dirt in and at the device should only be
removed by a specialist.
Liquids
• There must never enter any liquid into power outlets,
extension cords or any holes in the housing of the
device. If you suppose that also a minimal amount of
liquid may have entered the device, it must
immediately be disconnected. This is also valid, if the
device was exposed to high humidity. Also if the
device is still running, the device must be checked by
a specialist if the liquid has reduced any insulation.
Reduced insulation can cause mortal electrical shock.
Foreign Objects
• There must never be any objects entering into the
device. This is especially valid for metal parts. If any
metal parts like staples or coarse metal chips enter
into the device, the device must be taken out of
operation and disconnected immediately. Malfunction
or short-circuits caused by metal parts may cause
mortal injuries.
Maintenance and Service
• There are no serviceable parts inside the device.
Maintenance and service operations are only to be
carried out by authorized dealers!
• Disconnect from mains before cleaning! Never use
solvents or aggressive detergents in order to clean
the device! Rather use a soft and damp cloth.