background image

 

1. Safety 

 

1.1 General safety instructions 

 

Do not use this magnetic drilling machine before you have thoroughly read and completely 
understood this manual, specifically the “General safety instructions” and ‘’Specific safety 
information’’, including the figures, specifications, safety regulations and the signs indicating 
DANGER, WARNING and CAUTION. 
 

WARNING: 

When using electrical tools basic safety precautions should always be followed to 

reduce the risk of fire, electrical shock and personal injury. 

 
Please also observe the relevant national industrial safety regulations. Non-observance of the safety 
instructions can lead to an electric shock, burns and/or severe injuries. 
 
This manual should be kept for later use and enclosed with the magnetic drilling machine, should it 
be passed on or sold. 

 
Work area 

1.

 

Keep your work area clean and well lit. Cluttered and dark work areas increase the change of 

accidents; 

2.

 

Do not operate a magnetic drilling machine in explosive atmospheres, such as in the 

presence of flammable liquids, gases or dust. A magnetic drilling machine may create sparks 
which could ignite the dust or fumes; 

3.

 

Keep bystanders, children and visitors away while operating a magnetic drilling machine. 

Distractions can cause you to lose control. 

 
Electrical safety 

1.

 

A magnetic drilling machine plug must match the outlet. Never modify the plug in any way. 

Do not us any adapter plugs;  

2.

 

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. 

There is an increased risk of electric shock if your body is grounded; 

3.

 

Do not expose the magnetic drilling machine to rain or wet conditions. Water entering a 

machine will increase the risk of electric shock; 

4.

 

Do not abuse the cord. Never use the cord to carry the magnetic drilling machine or pull the 

plug from an outlet. Keep the cord away from heat, oil, sharp edges or moving parts. Replace 
damaged cords immediately. Damaged cords increase the risk of electric shock; 

5.

 

When operating a magnetic drilling machine, use an extension cord suitable for outdoor use, 

this reduces the risk of electric shock; 

6.

 

If operating a magnetic drilling machine in a damp location is unavoidable, use a residual 

current device (RCD), this reduces the risk of electric shock. 

 

 

Содержание ECO.55 Series








































Отзывы: