Euroboor BM45AIR Скачать руководство пользователя страница 20

Страница: 20 / 24

www.euroboor.com

5.1 Oil daily

The tool should be lubricated daily (or before each use) with air tool oil (included). During

continuous operation, the tool should be oiled every 1 to 2 hours. For lubricating it is

recommended to use 4 to 5 drops of oil in the air inlet. After which 30 seconds of running is

required to distribute the oil through the tool.

6. Troubleshooting

Problem

Possible Cause

Corrective Action

Tool runs slowly or will not

operate

No oil in tool.

Low air pressure.

Air hose leaks.

Pressure drops

Moisture blowing out of tool

exhaust.

Worn rotor blade.

Lubricate the tool with EUROBOOR

pneumatic oil IBO.80.

Adjust the compressor regulator to 90 PSI

and/or Adjust the regulator on the tool to

maximum setting.

Check the air hose for possible leaks and

repair these. Be sure the hose is the proper

size.

Do not use a multiple number of hoses

connected together with quick-connect

fittings.

Water in tank: drain tank. Oil tool and run

until no water is evident. Oil tool again and

run 1-2 seconds.

Abnormal vibration and/or

excessive heat

Improper lubrication.

Lubricate the tool with EUROBOOR

pneumatic oil IBO.80.

For any problems not in this troubleshooting table, contact your EUROBOOR distributor or

sales agent from whom purchased the tool.

Содержание BM45AIR

























Результаты поиска

Содержание BM45AIR

Отзывы:

Похожие инструкции для BM45AIR

Бренды по названию

Популярные бренды

Euroboor BM45AIR, Руководство оператора

Результаты поиска

Содержание BM45AIR

Отзывы:

Похожие инструкции для BM45AIR

Бренды по названию

Популярные бренды