background image

Assembly Instructions 
for the N!ergy 1210 Tent

A

B

A

B

D

C

fig 1

tent poles

fly poles

fig 8

fig 2

fig 5

Component List:

1 Tent    

2 Tent Poles 

1 Carry Bag 

1 Stake Bag W/Stakes 

 

1 Rain Fly

2 Fly Poles 

1 Pole Bag 

6 Pull Out Cords

1 Gear Loft 

1 Divider

1. 

Unroll and unfold the tent

 on the ground. Separate the rest of the 

components and place to one side. Open the door before pitching the 

tent. Do not stake the tent down (however, in windy conditions, stake 

down one corner that faces into the wind). 

2. 

Assemble all of the shockcorded poles.

 Keep the end sections from 

snapping together, as this can damage the ends. Make certain each 

plain end has been properly seated into the metal ferrule.

3. 

Insert an assembled pole

 

through both sleeves from 

A

 to 

B

. Insert the second pole through 

the sleeves from 

C

 to 

D

, forming 

an X across the tent. See fig 1.

There is a fabric loop at the tent’s 

peak. Capture this loop with the 

top pole as you move through 

the sleeves. See fig 1 & 2.

4. 

At A, insert the web corner pin

 into the end of the 

tent pole ferrule. At B, grasp the tent corner pin in one 

hand, the tent pole in the other. Arch the pole and 

place the pin into the end of the pole. See Fig 3 & 4.

Repeat this with the second pole from C to D raising the 

tent as you go. See fig 5. 

5. 

Start at the bottom and attach all the clips

 to 

the poles to create a freestanding tent. Place it in 

the desired location. See fig 6.

6. 

Stake the tent down

 through the 

corner loops. Stake the opposite corners 

while applying tension to smooth the 

floor wrinkles. Also, stake out the beckett 

beneath each of the side windows. See 

fig 7 & 8. 

7. 

Attach the fly to the poles.

 Lay out the fly with the inside side up, on ground at the front of 

the tent. Fit the fly poles into the pockets sewn to the hem. The poles run from side to side 

down the center of the fly forming an X. Secure the fly to the poles by wrapping the hook & 

loop fastener around the fly poles. See fig 9, 10 and 11.

8. 

Attach the fly to the tent

. Turn the fly assembly over and align it so 

that the poles point out over the doors. Grasp the corners of the of the 

fly and drag them up and over the roof to completely cover the tent. 

(This is much easier with two people) 

At the corners of the tent, reach under the fly and attach the hook & loop 

straps to the tent poles, securing the fly in place. See fig 12.

At the bottom/corners of the tent, attach the shockcorded J-hooks to the 

rings on the corner webs. See fig 13.

9. 

Tie a guy rope 

to each of the 4 

rings attached to the fly and stake 

out. Adjust tension with the in-line 

sliders. See fig 14 & 15.

YOUR TENT IS READY !

fig 4

fig 9

fig 10

fig 11

fig 7

fig 6

fig 12

fig 13

fig 15

fig 14

REV D 4.09

NOTE:

• Although it is possible to pitch this tent alone, it is faster/easier with two 

people. 

• Do not drop tent bag or pole bag on its end. Do not bounce tent bag on 

its end to get the tent out. These actions may cut the shockcord and/or 

damage the pole ends.

• The N!ergy series tents are pre-wired with three 12V outlets. Take care 

to keep them in their sleeves and avoid stepping on the sockets and 

wires during assembly.

fig 17

green

blue

fig 16

E! Power System: 

To use, you will need a power source. Our 

E! Power Pak™ 

is sold separately. Once connected to 

power, the control will display “green” at any switch that is “ON” and the “ON” socket will glow blue. See fig 16. 

E! Power Port:

 Open zipper and run extension cord through opening. 

Close zipper so that it rests next to the extension cord. Make sure the 

zipper cover is not twisted or tucked. The cover must lay flat against 

the outside of the tent to keep out rain.

Accessories: E! Power Fan/Light, E! Power Reading Light and an E! 

Power 12v Adapter Cord.

Sweep Out:

 Inside, at the bottom of the door is a sewn-in web loop. Pull 

this loop to the outside and stake it down to provide a ready exit for 

floor sweepings. See fig 17. 

Take Down:

 Pull up all stakes. Release the fly’s hook & loop straps. Remove fly. 

Remove fly poles. Remove clips from tent poles and pull poles off of the pins. 

Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it 

on tent. Roll up both towards the open door and stow.

Read the important safety instructions on the reverse side.

fig 3

Отзывы: