Fly pole
Awning
poles
Roof poles
Center
Wall poles
Corner
Wall poles
Component List:
1 Tent Body with Guy Ropes, 6 Wall Poles, 3 Roof Poles, 1 Fly Pole, 2-3 Awning Poles,
1 Fly, 1 Awning, 1 Divider Curtain, 1 Carry Bag, 1 Stake Bag/Stakes, 1 Pole Bag
2.
Assemble the shock corded
poles
and divide according to
size and shape. Take care;
make sure that each pole
section is fully seated into the
next. Do not allow the
sections to snap together as
this can damage the ends.
See fig 2.
1.
Remove from the carry bag
and separate all the components. Unroll and unfold the
fabric top side up, on a clean, dry space and open the doors. If windy, stake down the
windward corner. See fig 1.
4.
Raise the tent.
Start on one side and insert
black wall poles into the corner elbows. At the
bottom of each pole, insert the pin/ring
(attached to the corner web) into the
bottom of each pole. Next, install a
tan pole at the center. With the
tans, it works best to insert
the ring/pin first and then
fit the pole into the
elbow. See fig 5.
Repeat on the other side until the tent
is at full height and freestanding.
5.
Attach all clips
to the wall poles. See fig 6.
Stake the tent down through the corner web loops. Stake opposite corners while applying
tension to smooth the floor wrinkles. Next, align the center poles and stake down. Do this
before you add the fly. See fig 7.
Guy Out:
This tent has very large straight walls that act differently in high winds. If there are
high winds, carefully follow the guy out instructions on the back side of this sheet.
Awning:
If it's raining, lower both corner awning poles to create run-off channels. Loosen
shockcord on each corner pole, lower the angle of each pole and re-tighten guy lines.
Power Port:
Open zipper and run extension cord through opening. Close zipper so that it
rests next to the extension cord. Make sure the zipper cover is not twisted or tucked. The
cover must lay flat against the outside of the tent to keep out rain.
Take Down:
Pull up all stakes. Release the fly's hook & loop straps. Remove fly. Remove fly
poles. Remove clips from wall poles and pull poles off of the pins. Remove roof poles.
Collapse all poles and stow. Fold the tent onto itself then fold the fly and lay it on tent. Roll
up both towards the open door and stow.
Sweep Out:
Inside, at the bottom center of each
door is a sewn-in web loop. Pull this loop to the
outside and stake it down to provide a ready
exit for floor sweepings. See fig 16.
Options:
Floor Saver and Gear Loft
6.
Attach the fly to the pole.
Lay out the fly with the inside side up
,
on ground at the
front of the tent. Fit the fly pole into the pockets sewn to the hem. The pole runs from
side to side down the center of the fly. Secure the fly to the pole by wrapping the hook
and loop fasteners around the fly pole. See fig 8, 9 and 10.
7.
Attach the fly to the tent.
Turn the fly assembly over and align
it so that the pole ends point to the windows. Grasp the corners
of the of the fly and drag them up and over the roof poles to
completely cover the roof. ( This is much easier with two people.
) The end of the poles should point out over the windows.
At the corners of the tent, reach under the fly and attach the hook
& loop straps to the wall poles just below the elbow and down
the length of the wall poles, securing the fly in place. See fig 11.
At the bottom/corners of the tent, attach the shockcorded J-hooks
to the nylon rings on the corner web loops. See fig 12.
8.
Stake out the attached guy ropes
and adjust tension with the
in-line sliders.
9.
Install the awning.
Open the zippered flaps on the fly. See fig
13. Reach under the fly and clip the awning to the shockcords
on the corner elbows. See fig 14.
Tie a loop at each end of the guy ropes. Fit the pins
of the awning poles into the grommets at the hem
of the awning. Hang a guy rope loop over the pole
pin, stake the rope out and adjust tension as
needed. See fig 15.
Assembly Instructions for
Copper Canyon 1312 & 1512
YOUR TENT IS READY !
C
B
A
E
F
D
fig 2
fig 1
fig 5
fig 3
fig 6
fig 11
fig 12
fig 15
fig 16
fig 14
fig 13
fig 7
fig 8
fig 9
fig 10
3.
Insert both black roof poles
into the sleeves sewn on the tent body. They should
run corner to corner crossing in the center.
Fit one end of each into a nylon elbow attached to the roof corners at
A
and
B
. Move to
the opposite side, arch the poles and again fit into the nylon elbows at
C
and
D
.
Insert the gray roof pole, front to back, into the tan color coded sleeves from
E
to
F
. See
fig 3 and 4.
REV B 4.09
NOTE: One arm of each elbow
has interior ribs. Roof poles
insert into this ribbed arm.
Wall poles insert into the
plain arm.
fig 4
1512 has 3
awning poles
